Billy Goat Hurricane Z3000 Скачать руководство пользователя страница 42

Страница: 42 / 48

Not for

Reproduction

billygoat.com

Storage

STORAGE

Storing Machine Safety

CAUTION

Avoid injury! Fuel vapors are explosive and
fl ammable. Engine exhaust fumes contain
carbon monoxide and can cause serious
illness or death.

•

Run the engine only long enough to move the

machine to or from storage.

•

DO NOT

store vehicle with fuel in the tank inside

a building where fumes may reach an open

ame

or spark.

•

Allow the engine to cool before storing the ma-

chine in any enclosure.

Preparing Machine for Storage

1. Repair any worn or damaged parts. Replace

parts if necessary. Tighten loose hardware.

2. Remove debris from machine.

3. Wash the machine and apply wax to metal and

plastic surfaces.

4. Run

machine

for

ve minutes to dry belts and pul-

leys.

5. Apply light coat of engine oil to pivot and wear

points to prevent rust.

6. Check tire pressure.

Preparing Fuel and Engine For Storage

Fuel:

If you have been using “Stabilized Fuel,” add stabi-
lized fuel to tank until the tank is full. Turn OFF fuel
shutoff.

NOTE:

Filling the fuel tank reduces the amount of air

in the fuel tank and helps reduce deterioration of fuel.

If you are not using “Stabilized Fuel”:

1. Park machine safely in a well-ventilated area.

NOTE:

Try to anticipate the last time the machine will

be used for the season so very little fuel is left in the
fuel tank.

2. Turn ON engine and allow to run until it runs out

of fuel.

3. Turn key to OFF position.

4. Mix fresh fuel and fuel stabilizer in separate con-

tainer. Follow stabilizer instructions for mixing.

5. Fill fuel tank with stabilized fuel.

6. Run engine for a few minutes to allow fuel mixture

to circulate through carburetor on engine.

7. Turn OFF engine. Turn OFF the fuel shutoff.

Содержание Hurricane Z3000

















































Результаты поиска

Содержание Hurricane Z3000

Отзывы:

Похожие инструкции для Hurricane Z3000

Бренды по названию

Популярные бренды

Billy Goat Hurricane Z3000, Руководство пользователя

Результаты поиска

Содержание Hurricane Z3000

Отзывы:

Похожие инструкции для Hurricane Z3000

Бренды по названию

Популярные бренды