Billy Goat Hurricane Z3000 Скачать руководство пользователя страница 27

Страница: 27 / 48

Not for

Reproduction

Maintenance Procedures

Changing Engine Oil and Filter

IMPORTANT:

Avoid Damage! Change the oil more

often if the machine is used in extreme conditions:

•

Extremely dusty conditions.

•

Frequent slow or low-speed operation.

•

Frequent short trips.

1. Park machine safely.

2. Clean area around dipstick,

ller cap and

lter.

3. Make sure engine is cool.

4. Put oil drain pan beside engine on drain valve

side.

Oil Drain Valve

5. Place 18” of 1/2 ID hose on drain valve.

6. Open oil drain valve fully.

7. Allow oil to drain into an oil drain pan.

8. After oil drains, securely tighten oil drain valve.

9. Remove drain hose.

Oil Filter

IMPORTANT:

Make sure engine and exhaust system

is cool before proceeding. The oil

lter is located on

the left side of the engine.

10. Place some rags under the oil

lter to contain

spilled oil.

11. Turn oil

lter counterclockwise to remove. Pull the

oil

lter to remove past the muf

er.

12. Apply a

lm of clean engine oil to gasket of new

lter.

13. Install

lter. Turn

lter clockwise until gasket

makes contact with mounting surface. Tighten 1/2
to 3/4 turn after gasket contact.

IMPORTANT:

Do not use wrench to tighten oil

lter.

IMPORTANT:

Refer to engine manufacturer’s operat-

ing manual for correct type and grade of oil.

14. Add approximately 1.75 quarts of oil.

15. Insert dipstick. Replace oil

ller cap.

16. Start engine and run at slow throttle for approxi-

mately two minutes. Check for leaks around oil

lter and drain valve.

17. Stop engine.

18. Check oil level:

•

Remove dipstick. Wipe dipstick clean.

•

Insert dipstick fully and remove.

•

Add oil as needed to bring level to the FULL

mark without over

lling.

19. Insert dipstick.

Cleaning Engine Oil Cooler and Checking Air
Filter

Cleaning the Engine Oil Cooler

Keep engine oil cooler

ns clear of debris to ensure

proper cooling.

Refer to the engine manufacturer’s owner’s manual pro-
vided with your machine for the complete procedure.

Содержание Hurricane Z3000

















































Результаты поиска

Содержание Hurricane Z3000

Отзывы:

Похожие инструкции для Hurricane Z3000

Бренды по названию

Популярные бренды

Billy Goat Hurricane Z3000, Руководство пользователя

Результаты поиска

Содержание Hurricane Z3000

Отзывы:

Похожие инструкции для Hurricane Z3000

Бренды по названию

Популярные бренды