Billy Goat Hurricane Z3000 Скачать руководство пользователя страница 43

Страница: 43 / 48

Not for

Reproduction

Storage

Engine storage:

1. Change

engine

oil

and

lter while engine is warm.

2. Service

air

lter if necessary.

3. Clean debris from engine air intake screen.

4. Remove spark plugs. Put 1 oz. of clean engine oil

in cylinders. Install spark plugs, but do not con-
nect spark plug wires. Crank the engine

ve or six

times to allow oil to be distributed.

5. Clean the engine and engine compartment.

6. Remove

battery.

7. Clean the battery and battery posts.

8. Close fuel shut-off valve.

9. Store the battery in a cool, dry place where it will

not freeze.

NOTE:

The stored battery should be recharged every

90 days.

10. Store the vehicle in a dry, protected place.

NOTE:

Put a waterproof cover over on machine if

stored outside.

Removing Machine From Storage

1. Check tire pressure.

2. Check engine oil level.

3. Check battery. Charge battery if necessary.

4. Install

battery.

5. Check spark plug gap. Install and tighten plugs to

speci

ed torque.

6. Open fuel shut-off valve.

7. Run the engine 5 minutes at mid throttle with de-

ectors closed to allow oil to be distributed

throughout engine.

8. Be sure to test all safety systems before operat-

ing.

Содержание Hurricane Z3000

















































Результаты поиска

Содержание Hurricane Z3000

Отзывы:

Похожие инструкции для Hurricane Z3000

Бренды по названию

Популярные бренды

Billy Goat Hurricane Z3000, Руководство пользователя

Результаты поиска

Содержание Hurricane Z3000

Отзывы:

Похожие инструкции для Hurricane Z3000

Бренды по названию

Популярные бренды