Billy Goat Hurricane Z3000 Скачать руководство пользователя страница 14

Страница: 14 / 48

Not for

Reproduction

billygoat.com

Safety and Operational Decals

DECALS

Before operating your unit, read the safety decals.
The cautions and warnings are for your safety. To
avoid a personal injury or damage to the unit,
understand and follow all safety decals.

WARNING

If any safety decals become worn or
damaged, and cannot be read, order
replacement decals from your local dealer.

EMERGENCY BRAKE

RELEASE

LIFT LEVER

X3-4211

KEEP HANDS AND FEET AWAY

FUEL FILL (GASOLINE ONLY)

FORWARD

REVERSE

FORWARD

REVERSE

DANGER

WARNING

DO NOT OPERATE THIS EQUIPMENT
WITHOUT PROPER AUTHORIZATION

AND TRAINING. IT IS THE OPERATOR’S

RESPONSIBILITY TO READ AND

COMPLETELY UNDERSTAND ALL

DANGERS, WARNINGS, CAUTIONS AND

INSTRUCTIONS ON THE EQUIPMENT

AND IN THE OPERATOR’S MANUAL.

PARKING BRAKE

RED DOTTED LINE = BRAKE AUTOMATICALLY ENGAGED

GRAY FILL = BRAKE AUTOMATICALLY DISENGAGED

CAUTION

PINCH

POINT

ALL

Callout

Part Number

Description

84001535

Decal, Emergency Brake Release

84001443

Decal, Transaxle Bypass Valve

84001491

Decal, Pinch Point

84001867

Decal, Dash, Joystick

84001490

Decal, Danger

84001489

Decal, Hot

84001493

Decal, Dash Controls

84001492

Decal, Hydro

Содержание Hurricane Z3000

















































Результаты поиска

Содержание Hurricane Z3000

Отзывы:

Похожие инструкции для Hurricane Z3000

Бренды по названию

Популярные бренды

Billy Goat Hurricane Z3000, Руководство пользователя

Результаты поиска

Содержание Hurricane Z3000

Отзывы:

Похожие инструкции для Hurricane Z3000

Бренды по названию

Популярные бренды