Beta RR 4T-250 Скачать руководство пользователя

Страница: 177 / 215

CHECKS AND MAINTENANCE

114

CHECK THE LEVEL OF THE FRONT BRAKE

FLUID

Check the level of the brake fluid through

sight

. The level of the fluid should never

fall below the mark in the sight.

RESTORING THE LEVEL OF THE FRONT

BRAKE FLUID

To restore the level of the brake fluid, loosen

the two screws

, lift cap

and add brake

fluid (IP DOT 4) until its level is 5 mm be-

low the upper rim of the reservoir.

WARNING

We recommend using DOT 4 brake fluid.

Should this fluid be unavailable, use DOT

5.1 fluid instead. Do not on any account

use DOT 5 brake fluid. This is a purple

fluid with a base of silicone oil which re-

quires special seals and tubes.

WARNING

The brake fluid is extremely corrosive. Take

care not to spill it on the paintwork.

BLEEDING THE FRONT BRAKE

Follow these steps to bleed the front brake

circuit:

•

Remove rubber cap

from valve

•

Remove the oil reservoir cap.

•

Insert one end of a small tube into valve

and place the other end in a container.

•

Unscrew valve B (while pulling the brake

lever) and then pump by repeatedly ac-

tuating the brake lever until oil starts flow-

ing out continuously with no air bubbles.

During this operation, it is important that

the lever should not be released com-

pletely and that the brake pump reser-

voir should be continuously refilled to

make up for the oil that is flowing out.

•

Tighten the valve and extract the tube.

•

Replace the cap.

•

Replace the fluid reservoir cap on the

brake pump.

Содержание RR 4T-250
























































































































































































































Результаты поиска

Содержание RR 4T-250

Отзывы:

Похожие инструкции для RR 4T-250

Бренды по названию

Популярные бренды

Beta RR 4T-250, Руководство по ремонту

Результаты поиска

Содержание RR 4T-250

Отзывы:

Похожие инструкции для RR 4T-250

Бренды по названию

Популярные бренды