Bernina dcet 2500 Скачать руководство пользователя страница 73

Страница: 73 / 82

Trouble shooting guide

Problem:

Cause:

Solution:

Seams pucker:

Differential feed is

Adjust differential feed to 0.7 - N.

set incorrectly.

Needle thread tensions

Reduce needle thread tensions.

are too tight.

Looper thread tension is

Use the Deco Guide.

too tight for thread.

Fabric edges curl:

Too much fabric in the stitch.

Reduce the cutting width.

Stitch selection lever is

Set selection lever to overlock.

on roll hem.

Thread loops are too loose.

Too little fabric in the stitch.

Increase the cutting width.

Machine stops sewing:

Should the machine stops

Check why the machine stopped. The machine will sew

sewing, the motor cuts out

again after the safety cut out.

for 2 seconds, afterwards
you can continue sewing.

Fabric cannot be removed:

Handwheel was turned anti-

Insert needles into fabric, press Needle stop, turn the

(cover stitch and

clockwise.

handwheel away from you (clockwise) to raise needles.

top & bottom cover stitch)

Remove work.

2500_DCE_2_englisch_neu 09.10.2007 15:02 Uhr Seite 73

Содержание dcet 2500

















































































Результаты поиска

Содержание dcet 2500

Отзывы:

Бренды по названию

Популярные бренды

Bernina dcet 2500, Инструкция по эксплуатации

Результаты поиска

Содержание dcet 2500

Отзывы:

Бренды по названию

Популярные бренды