Bergoz MX-BPM страница 32 Скачать руководство пользователя | Manualshive

Страница: 32 / 49

background image

ACCESSORIES (Cont’d)

Card Extender BPM-XTD

The card extender allows access to the BPM module adjustments while it is connected to the
chassis, thus to the readout and control system.

The BPM-XTD is not as convenient as the BPM-KIT for adjustments.

The coaxial connections extensions of the button signals cause an offset of the X and Y outputs
when the extender is used. This is due to the difference in signal attenuation between the 4
extension cables. These differences are recorded on a label affixed to the extender.

TTL Commands Service module BPM-SERV/CMD

Not available at the time this manual is written.

The TTL Commands Service module can be inserted in a BPM station of a chassis, in place of the
BPM module.

It brings to the front panel:

• On a DB9 female connector, the External Commands applied by the control system to this station

Similar connector pin-out as used on BPM-RFC/X and BPM-KIT, but reversed gender.

• On a DB15 male connector, the Output lines to which the BPM module would apply its Outputs.

Similar connector pin-out as used on BPM-RFC/X and BPM-KIT, but reversed gender.

This module is useful because access to the cables at the rear of the chassis will be very difficult.
With this module, one can:

(a) Observe and debug the signals sent by the control system to a BPM station
(b) Feed known signals into the BPM readout system, to test it.

RF Service module BPM-SERV/RF

Not available at the time this manual is written.

The RF Service module can be inserted in a BPM station of a chassis, in place of the BPM module.

It brings to the front panel –on SMA jacks– the four signals applied to this BPM station by the
BPM buttons.

For oscilloscope and spectrum analyser viewing of the BPM button signals.

Very useful, because the RF cables at the rear of the chassis are too crowded to be disconnected.

BERGOZ Instrumentation

Multiplexed

01630 Saint Genis Pouilly, France

Beam Position Monitor

Tel. +33-450.426.642
Fax +33-450.426.643

Page 30

User’s manual

BERGOZ Instrumentation - 01630 Saint Genis Pouilly, France - Tel.: +33-450.426.642 - Fax: +33-450.426.643

email: [email protected] - http://www.bergoz.com - Registre des Métiers: Bourg-en-Bresse - Registre des ingénieurs: Zurich

TVA-VAT-IVA-USt. Nº FR88414997130 - Sàrl. capital 152K - Siren 414 997 130 R.C.S. Bourg - APE 332B

«
...
30
31
32
33
34
...
»

Содержание MX-BPM


















































Отзывы:

Нет отзывов

Похожие инструкции для MX-BPM

Бренд: VAC Страницы: 16

Бренд: GE Страницы: 18

Masoneilan SVI FF

Бренд: GE Страницы: 32

Baker Hughes Masoneilan SVI FF

Бренд: GE Страницы: 264

Бренд: GE Страницы: 292

Бренд: Genebre Страницы: 9

Бренд: Genebre Страницы: 11

Бренд: Genebre Страницы: 14

Бренд: Genebre Страницы: 15

Бренд: FIAMA Страницы: 11

Бренд: Aventics Страницы: 5

Бренд: Aventics Страницы: 6

Бренд: Aventics Страницы: 7

Бренд: Aventics Страницы: 9

Бренд: KAUP Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды