manualshive.com logo in svg

Bergoz MX-BPM, Руководство пользователя

Поделиться
Скачать
Bergoz MX-BPM Скачать руководство пользователя страница 30

CONNECTORS PINS ALLOCATION  Rev. 4.0

Connectors on Table-top test kit BPM-KIT and Chassis BPM-RFC/X

BPM Module rear connector
Rear connector DIN 41612, 
form M, 3 rows of 8 pins each, + 2 groups of 4 coax 1.0/2.3 connectors

DB9 female front panel connector
Button inputs

Signal

Button A

.................................. BUTA...........

........... b2

Button B

.................................. BUTB...........

........... b5

Button C

.................................. BUTC...........

........... b8

Button D

.................................. BUTD...........

...........b11

Auxiliary fast signals

Fast gate

.................................. GATE...........

...........b22

Reserved (RF signal out)  ............................ RFOUT.........

...........b25

Reserved (Local oscillator)  .......................... LOIN............

...........b28

Not allocated

.................................. free..............

...........b31

DB9

Common external commands

 male

Single button sampling mode.........................SBS*............

...........b17 ............2

Button address

Upper bit....................... BADD1*........

...........b16 ............3

Lower bit.......................BADD0*........

...........c17 ............4

Reset (single button mode)............................PHRESET*....

...........b15 ............5

AGC disable

.................................. AGCD*.........

...........b13 ............7

Sampling clock (inhibits on-board clock)........... CLK*........... 6 ...........c16 ............8
Reserved

.................................. free..............

...........a19

Ground

.................................. GND............

...........c14 ............9

Reserved

.................................. ...................

...........b18 ............1

DB15

Input and output signals 

female

Ground (signal ground for all outputs)..............GND............ 5 ...........a20 .......... 15
PLL demodulator in lock output......................PLLOCK.......

...........a13 ............1

AGC voltage output .................................. VAGC........... 3 ...........c19 ............2
X (also button value in single button mode)........ XOUT........... 4 ...........c20 ............3
Y output

.................................. YOUT........... 8 ...........b19 ............4

Σ 

output

.................................. SOUT...........

...........b20 ............5

A button signal output................................. AOUT...........

...........a17 ............6

B button signal output................................. BOUT...........

...........a18 ............7

C button signal output................................. COUT...........

...........a15 ............8

D button signal output................................. DOUT...........

...........a16 ............9

Sync. from sampling clock........................... SYNC........... 9 ...........b14 .......... 10
Synchronous demodulator output....................SDEMOD....... 7
Peak demodulator output (single button mode).....PDEMOD....... 1
External gain setting input.............................GAIN........... 2 ...........a14 .......... 13

Power Supply

+15V

.................................. +15V............

...........c13

–15V

.................................. -15V.............

...........c15

0V (power supply ground)............................GND............

...........c14

*Active low

BERGOZ Instrumentation

Multiplexed

01630 Saint Genis Pouilly, France

Beam Position Monitor

Tel. +33-450.426.642
Fax +33-450.426.643

Page 28

User’s manual

                                                                                                                                                                    

                                                                                                                                                                         

BERGOZ Instrumentation  -  01630 Saint Genis Pouilly, France - Tel.: +33-450.426.642  -  Fax: +33-450.426.643

email: [email protected] - http://www.bergoz.com - Registre des Métiers: Bourg-en-Bresse - Registre des ingénieurs: Zurich

TVA-VAT-IVA-USt. Nº FR88414997130  -  Sàrl. capital 152K  -  Siren 414 997 130  R.C.S. Bourg  - APE 332B

Содержание MX-BPM


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды