manualshive.com logo in svg

Bergoz MX-BPM, Руководство пользователя

Поделиться
Скачать
Bergoz MX-BPM Скачать руководство пользователя страница 19

SINGLE BUNCH / SINGLE BEAM MODE

The Fast Gate option (BPM-FG) allows to monitor the position of a single bunch out of a beam, or 
to separate beams in colliders, provided the selected bunch can be fitted in the gate of 20 ns 
minimum width.   The BPM-FG option consists of a modified GaAs switch driver –with a NIM 
pulse command– replacing the standard switch driver, and the addition of the GATE input 
connector.

The Fast Gate may be used with the Closed Orbit mode and with the Single Button Sampling mode.
• In Closed Orbit mode, the Fast Gate allows to monitor the average position of a single bunch, or 

selected bunches.

• In First Turn mode, the Fast Gate allows to capture the first turn only, or any other subsequent 

turn.

The gate is defined by:

GATE

External fast NIM gate. Only with option BPM-FG.
Gate width 

≥

 20 ns.

The Fast Gate feature works like this:

• When no signal is applied to GATE (disconnected), the Fast Gate feature is not active.

• When GATE is pulled down by a NIM (-20 mA) signal, all multiplexer GaAs switches 

remain open (non-conducting).

• When GATE is released high (0 mA), the GaAs switch addressed by the button address lines 

BADD0 and BADD1 closes (conducting).

Fast Gate timing

≥

 20 ns

Beam

GATE

0

GaAs switch

non-conducting

non-conducting

conducting

Gated bunches

To display the above signals in their correct time relation, the service module BPM-SERV/RF can 
be inserted in place of a BPM module.  It provides the RF signals BUTA, BUTB, BUTC, BUTD 
and the delayed GATE signal.

BERGOZ Instrumentation

Multiplexed

01630 Saint Genis Pouilly, France

Beam Position Monitor

Tel. +33-450.426.642
Fax +33-450.426.643

Page 17

User’s manual

                                                                                                                                                                    

                                                                                                                                                                         

BERGOZ Instrumentation  -  01630 Saint Genis Pouilly, France - Tel.: +33-450.426.642  -  Fax: +33-450.426.643

email: [email protected] - http://www.bergoz.com - Registre des Métiers: Bourg-en-Bresse - Registre des ingénieurs: Zurich

TVA-VAT-IVA-USt. Nº FR88414997130  -  Sàrl. capital 152K  -  Siren 414 997 130  R.C.S. Bourg  - APE 332B

Содержание MX-BPM


















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды