Bergoz MX-BPM страница 6 Скачать руководство пользователя

Страница: 6 / 49

QUICK CHECK (Cont'd)

If you have a 19” chassis (BPM-RFC/X), use the following set-up:

DVM

RF Source

Power
splitter

Oscilloscope

Ch.1 Ext. trig.

To button inputs
(back of chassis)

Attach the equipment together as shown above.

Set the oscilloscope time base on 0.2 ms / div.
Ext. trigger connects to SYNC signal, trigger level 0.2V, 1 M

Ω

AC coupling

Channel 1 to SDEMOD signal, sensitivity 0.1 V / div., 1 M

Ω

AC coupling

Set the RF source to the operating frequency.
Amplitude ca. -13 dBm
Note: The BPM module operating frequency is written on the F–Key daughter board.

To access the F–Key, remove the BPM module shield.

Set the X and Y voltmeters range in such a way that millivolts are readable.
Connect to AC mains, the oscilloscope should display:

Synchronous demodulated signal.
Each period 100…125µs represents
the successive buttons A, B, C, D, A, B…

The signals are equalized before delivery
of the BPM module, using a precision
input 4-way splitter.

Differences in signal level as shown here
are due to uneven input signals.

Note: 1 dB input signal difference gives
ca. 300 mV of demodulated signal
amplitude difference

BERGOZ Instrumentation

Multiplexed

01630 Saint Genis Pouilly, France

Beam Position Monitor

Tel. +33-450.426.642
Fax +33-450.426.643

Page 4

User’s manual

BERGOZ Instrumentation - 01630 Saint Genis Pouilly, France - Tel.: +33-450.426.642 - Fax: +33-450.426.643

email: [email protected] - http://www.bergoz.com - Registre des Métiers: Bourg-en-Bresse - Registre des ingénieurs: Zurich

TVA-VAT-IVA-USt. Nº FR88414997130 - Sàrl. capital 152K - Siren 414 997 130 R.C.S. Bourg - APE 332B

Содержание MX-BPM


















































Результаты поиска

Содержание MX-BPM

Отзывы:

Похожие инструкции для MX-BPM

Бренды по названию

Популярные бренды

Bergoz MX-BPM, Руководство пользователя

Результаты поиска

Содержание MX-BPM

Отзывы:

Похожие инструкции для MX-BPM

Бренды по названию

Популярные бренды