Bergoz MX-BPM Скачать руководство пользователя | Manualshive

Страница: 35 / 49

background image

BPM MODULE REAR CONNECTOR DIN41612M 24+8

Note: For connections, See Connector Pins Allocation, this manual.

BPM chassis for 1 up to 16 BPM modules are part of Bergoz Instrumentation sales program (BPM-
RFC/X) and include the necessary mating connectors (See BPM chassis, this manual).
The following is of interest to those who wish to design their own chassis.

The BPM module rear connector commonly designated DIN41612M 24+8 is a male connector with
24 pin contacts and 8 holes for coaxial connectors. V42254-B1200-M240 from Siemens is the
reference used.

The coaxial connectors inserted in the rear connector are of the “jack”-type series 1.0/2.3.
Four V23601-A1227-E1 from Siemens are used for button inputs (jack, right angle, soldering type)
One V23601-A602-E71 from Siemens is used for the optional Fast Gate (jack, straight, crimp)

On the chassis side (or “Backplane” side), for each BPM module, the following is needed:

• One DIN41612M female connector with 24 pin contacts and 8 holes for coaxial connectors.
We recommend using Siemens connectors to assure compatibility:
V42254-B2240-M240 from Siemens, for wrapping connection
V42254-B2202-M240 from Siemens, for soldering connection (4.5-mm pins)
Other references available for press-fit connection.

• Four or five coaxial “plug”-type connectors, series 1.0/2.3.
A large number of manufacturers produce these connectors. However, to assure good connector
mating, we recommend that you use connectors from Siemens:
V23601-B302-E71 or V23601-A302-E71 for straight cable attachment to RG316 (Øext.

≤

2.6mm)

V23601-A302-E1 for straight cable attachment to RG178 (Øext.

≤

1.9mm)

V23601-A502-E71 (18.7mm long) for 90° angle cable attachment.to RG316 (Øext.

≤

2.6mm)

V23601-A556-E71 (22.3mm long) for 90° angle cable attachment.to RG316 (Øext.

≤

2.6mm)

V23601-A502-E73 (18.7mm long) for 90° angle cable attachment.to RD316 (Øext.

≤

3.0mm)

V23601-A556-E73 (22.3mm long) for 90° angle cable attachment.to RD316 (Øext.

≤

3.0mm)

Cable type correspondence:

US manufacturers’ designation

VDE designation

IEC designation

RG316

5YC5Ye 0,5/1,5

50-2-1

RD316

5YCC5Y 0,5/1,5

--

RG178

5YC5Ye 0,3/0,86

50-1-1

Siemens recommends to use connector crimping tool reference M1002-K1.

BERGOZ Instrumentation

Multiplexed

01630 Saint Genis Pouilly, France

Beam Position Monitor

Tel. +33-450.426.642
Fax +33-450.426.643

Page 33

User’s manual

BERGOZ Instrumentation - 01630 Saint Genis Pouilly, France - Tel.: +33-450.426.642 - Fax: +33-450.426.643

email: [email protected] - http://www.bergoz.com - Registre des Métiers: Bourg-en-Bresse - Registre des ingénieurs: Zurich

TVA-VAT-IVA-USt. Nº FR88414997130 - Sàrl. capital 152K - Siren 414 997 130 R.C.S. Bourg - APE 332B

«
...
33
34
35
36
37
...
»

Содержание MX-BPM


















































Отзывы:

Нет отзывов

Похожие инструкции для MX-BPM

PSE3**PN series

Бренд: halstrup-walcher Страницы: 35

Бренд: +GF+ Страницы: 4

Бренд: FIAMA Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды