Beretta METEO GREEN HE R.S.I., Инструкция по установке и эксплуатации

Страница: 40 / 56

40
METEO GREEN HE R.S.I.
3.1.1 Selecting the operating mode
SUMMER MODE (boiler in STAND-BY)
WINTER MODE
heating
To select the winter operating mode, press the “ ” button.
To select the desired winter operating mode, press the AUTO/MAN
button until you see the corresponding symbol on the display.
The display shows one of the available winter operating modes:
MANUAL MODE
When the symbol “ ”, is displayed,
the remote control panel operates as
ROOM THERMOSTAT .
In the “ ” operating mode, the boiler
works “manually”, that is to say inde-
pendently of the time bands set in the
heating schedule (paragraph 3.2.4.
HTG-PROG dedicated section). As a
result, the heating works continuously at the selected temperature
(see USER MENU).
To modify the room temperature, see section “Adjusting the preset
data” paragraph 3.2.3, “T-ROOM” dedicated section.
NIGHT OPERATING MODE
When the “ ”,symbol is displayed,
the heating is off.
he heating function will enable only if
the room temperature falls below the
reduced temperature set (T-REDU-
CED - see USER MENU, paragraph
3.2.4)..
To adjust the reduced temperature
values, see chapter “Adjusting the preset data” paragraph 3.2.3.,
“T-REDUCED” dedicated section)
AUTOMATIC OPERATING MODE
When the “ ”, s displayed, the re-
mote control panel operates as PRO-
GRAMMABLE ROOM THERMO-
STAT
, given the heating time bands
scheduled. The time bands are three
and they identify with the symbols:
e - -
To adjust them, see the paragraph
3.2.4 “HTG-PROG” dedicated section
In the “ “ operating mode, the boiler works “automatically”.
To adjust the room temperature values, see chapter “Adjusting the
preset data” paragraph 3.2.3., “T-ROOM” dedicated section.
To return to the automatic ope-
rating mode after a period of
manual functioning, you need to
press the button AUTO/MAN until the
display shows the“ ” symbol.
T-AMB1/T-ROOM DES1
T-RIDOTTA/T-REDUCED
3.1.2 Selector for adjusting the room temperature
set
In the manual and automatic ope-
rating modes, the heating function
depends on the room temperature
values set.
These values can be adjusted with
± 5°C by turning the selector – see
•`^[ƒ
To adjust the temperature, proceed
as follows:
-
to increase the temperature
set, turn the selector to the right,
-
to decrease the temperature
set, turn the selector to the left.
It is not possible to use the selector for adjusting the domestic
hot water temperature.
[>?@<•\'<?&@?[&?'|^?@`[\&†[}}['?&'[^[@`[@
temperature set (night operating mode).
3.1.3 Interrupting the heating schedule
PAUSE
The PAUSE function is active only in
the and - - - ope-
rating mode.
During this phase, the boiler does not
operate and it will start over when the
'<>[ {\&@ [' < •&<[@ ?^
when the room temperature falls un-
der the reduced temperature set.
If you press the PAUSE button If you
press the PAUSE button once, the
display shows four zeros in the room
'[>|[^\'`^[•[]@ƒ
} }?^–[ƒ}^?>'[•^'
pressing you do not make
\&†>?@<•\'<?& '[|\&[]
exits the function.
Another time, you can move on to set
the interruption time bands, which can
reach a maximum of 24 hours.
[@<|]\†\||[\^\<&•`^[ƒ
Each pressing of the
PAUSE button
increases the interruption time band
with 1 hour.
Each pressing of the AUTO/MAN button decreases the interruption
time band with 1 hour.
The “PAUSE” function enables right after the PAUSE hours are set
and disables when they are over.
To exit the PAUSE function before the time set is over, you have
to press the “ “, button; after some seconds the PAUSE word
disappears from the display.
Press again the “ ” button, to select the function desired.
PAUSE
AUTO MAN
PAUSE
AUTO MAN
selettore correzione
temperatura ambiente (± 5°C)
selector for adjusting the room
temperature (± 5°C)
PAUSE
AUTO MAN
PAUSE
AUTO MAN