Berchtold OPERON B 810 Скачать руководство пользователя страница 95

Страница: 95 / 120

OPERON B 810 SURGICAL TABLE

SERVICE PROGRAM

6-24 Rev.

70-000-0027

No.

Error

Reaction Description

Solution

Valve-14 fault
(KIDNEY UP)

Continue Valve disconnected, wiring broken, short

circuit, damaged solenoid coil

•

Connect valve.

•

Identify and replace
broken wiring.

•

Locate and remove
cause of short circuit.

•

Replace the Solenoid
coil.

Hand Pendant fault Continue Push button defective during initial test,

wiring broken
NOTE: This error code will be recorded if
the operator presses two or more buttons
when switching the pendant on from “sleep”
mode.

•

Check connection

•

Check all pendant
functions. Replace
pendant if functions
to not operate as
expected.

Foot Control Panel
fault

Continue Pedal pressed or defect during initial test

NOTE: This error code will be recorded if
the operator presses two or more buttons
when switching the foot control on from
“sleep” mode.

•

Check connection

•

Check all footswitch
functions. Replace
footswitch if
functions do not
operate as expected.

Event:
Communication
command “Reset”

Reset

Micro controller was reset by communication
command "Reset"

No action required.

Reset Instruction
Executed

Reset

Micro controller was reset by software
instruction

No action required.

Watchdog timeout
reset

Reset

Oscillator / Crystal 10 MHz defective,
incorrect frequency

•

Non-critical error.

•

Run table through all
functions to ensure
proper operation. If
functions fail to
operate as expected,
replace the CPU.

61 Brown-out

reset Reset

Supply voltage for the Micro controller
(n5V) is between 4.2 volt and 4.6
volt. Battery almost discharged, Voltage
Regulator defective

•

Charge battery

•

Replace charging
circuit

Stack
overflow/underflow

Reset

Runtime error in the software caused by
inadequate program memory

Replace the CPU

Unknown RESET
condition

Reset

Micro controller was reset through unknown
cause
NOTE: This error can be caused by
electromagnetic radiation strong enough to
penetrate the table’s shielding.

No action required.

If problem persists
check for EMI source

Event: Power Up
(First time ON)

Continue This is not an error. It is a counter that

records the "Power Up" events.

No action required.

1 Missing numbers in the sequence indicate error codes reserved for future releases. If you receive an unnumbered error code, contact

Berchtold Technical Service for assistance.

Содержание OPERON B 810

























































































































Результаты поиска

Содержание OPERON B 810

Отзывы:

Похожие инструкции для OPERON B 810

Бренды по названию

Популярные бренды

Berchtold OPERON B 810, Запасные части

Результаты поиска

Содержание OPERON B 810

Отзывы:

Похожие инструкции для OPERON B 810

Бренды по названию

Популярные бренды