manualshive.com logo in svg

Berchtold OPERON B 810, Запасные части

Berchtold OPERON B 810 - высококачественный продукт, предназначенный для медицинских учреждений. Этот операционный стол оборудован всеми необходимыми сервисными частями для эффективной работы. Скачайте бесплатное руководство по эксплуатации на manualshive.com, чтобы узнать больше о функциональности и использовании этого устройства.

Поделиться
Скачать
background image

OPERON B 810 SURGICAL TABLE 

  

TABLE 

OF 

CONTENTS

 

70-000-0027  

Rev. 

1 

  

i 

TABLE OF CONTENTS 

SPECIAL SAFETY INSTRUCTIONS.................................................................................................................. S-1

 

SAFETY SYMBOLS......................................................................................................................................... S-1

 

USE CONDITIONS........................................................................................................................................... S-1

 

POWER SUPPLY .............................................................................................................................................. S-1

 

PINCH POINTS................................................................................................................................................. S-1

 

LOAD CAPACITY............................................................................................................................................ S-2

 

PATIENT POSITIONING ................................................................................................................................. S-3

 

PATIENT ORIENTATION ............................................................................................................................... S-3

 

OPERATION ..................................................................................................................................................... S-3

 

TABLE MOVEMENT WITH PATIENT .......................................................................................................... S-3

 

PRIMARY HAND PENDANT FUNCTIONS .................................................................................................. S-3

 

AUXILIARY HAND PENDANT...................................................................................................................... S-3

 

HEADREST....................................................................................................................................................... S-4

 

REMOVABLE LEG SECTION......................................................................................................................... S-4

 

ACCESSORIES DESIGNED BY OTHERS ..................................................................................................... S-4

 

RADIOLUCENT TABLE TOP AND PADS .................................................................................................... S-4

 

FOOTSWITCH (OPTIONAL)........................................................................................................................... S-4

 

HYDRAULIC SYSTEM.................................................................................................................................... S-4

 

HOLLOW PLUGS............................................................................................................................................. S-4

 

HYDRAULIC FLUID........................................................................................................................................ S-4

 

ELECTROMAGNETIC INTERFERENCE....................................................................................................... S-5

 

ELECTRICAL SYSTEM................................................................................................................................... S-5

 

SERVICE PROGRAM....................................................................................................................................... S-5

 

CLEANING AND DISINFECTION ................................................................................................................. S-6

 

WARNING LABELS ........................................................................................................................................ S-6

 

GENERAL INFORMATION..................................................................................................................................1-1

 

GENERAL DESCRIPTION ...............................................................................................................................1-1

 

RADIOLUCENT TABLE TOP AND PADS .....................................................................................................1-1

 

INTERCHANGEABLE HEADREST ................................................................................................................1-1

 

POWER SUPPLY ...............................................................................................................................................1-2

 

FUSES.................................................................................................................................................................1-2

 

FLOOR LOCK SYSTEM ...................................................................................................................................1-3

 

PRIMARY HAND PENDANT...........................................................................................................................1-3

 

PRIMARY HAND PENDANT INDICATORS ......................................................................................... 1-4

 

PRIMARY HAND PENDANT FUNCTIONS ........................................................................................... 1-5

 

FOOTSWITCH (OPTIONAL)............................................................................................................................1-6

 

MANUAL FOOT PUMP ....................................................................................................................................1-6

 

AUXILIARY HAND PENDANT.......................................................................................................................1-7

 

AUXILIARY PENDANT STORAGE................................................................................................................1-7

 

OPERATING INSTRUCTIONS.............................................................................................................................2-1

 

PINCH POINTS..................................................................................................................................................2-1

 

ELECTROMAGNETIC INTERFERENCE........................................................................................................2-1

 

LOAD CAPACITY.............................................................................................................................................2-1

 

Содержание OPERON B 810

























































































































Отзывы:

Нет отзывов

Похожие инструкции для OPERON B 810

UFO Vega Product User Manual preview
Vega
Бренд: UFO Страницы: 16
e+p Elektrik Handels HDT 300 Quick Installation Manual preview
HDT 300
Бренд: e+p Elektrik Handels Страницы: 2
JBL EON15 Introduction And General Information preview
EON15
Бренд: JBL Страницы: 38
JBSYSTEMS Light FALCON Operation Manual preview
FALCON
Бренд: JBSYSTEMS Light Страницы: 32
JBM 53724 Manual preview
53724
Бренд: JBM Страницы: 12
laerdal MegaCode Kelly Manual preview
MegaCode Kelly
Бренд: laerdal Страницы: 8
LAHTI PRO 46018 User Manual preview
46018
Бренд: LAHTI PRO Страницы: 16
laerdal LSU Directions For Use Manual preview
LSU
Бренд: laerdal Страницы: 32
laerdal Resusci Anne Important Product Information preview
Resusci Anne
Бренд: laerdal Страницы: 32
laerdal ALS Simulator Manual preview
ALS Simulator
Бренд: laerdal Страницы: 8
MacDon A30-S Assembly Instructions Manual preview
A30-S
Бренд: MacDon Страницы: 46
MacDon 5020 Operator'S Manual preview
5020
Бренд: MacDon Страницы: 82
Mac Medical PTF1000 Preparations For Using preview
PTF1000
Бренд: Mac Medical Страницы: 2
MACDEV CYBORG User Manual preview
CYBORG
Бренд: MACDEV Страницы: 8
MAC TOOLS Mentor Touch ET750 Operating Instructions Manual preview
Mentor Touch ET750
Бренд: MAC TOOLS Страницы: 24
MA lighting MA Switch Repair Instructions preview
MA Switch
Бренд: MA lighting Страницы: 10
QRS PMII Upgrade Instructions preview
PMII
Бренд: QRS Страницы: 16
QMAXZ Lighting QS Series User Manual preview
QS Series
Бренд: QMAXZ Lighting Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды