Berchtold OPERON B 810 Скачать руководство пользователя страница 7

Страница: 7 / 120

OPERON B 810 SURGICAL TABLE

TABLE

CONTENTS

70-000-0027

Rev.

TABLE OF FIGURES

FIGURE S-1

MAXIMUM WEIGHT LOCATION ........................................................................................ S-2

FIGURE S-2

PATIENT SAFETY WARNING LABEL ................................................................................ S-6

FIGURE S-3

FUSE LABEL.............................................................................................................................. S-6

FIGURE 1-1

OPERON B 810 SURGICAL TABLE .......................................................................................1-1

FIGURE 1-2

BASE COMPONENTS ...............................................................................................................1-2

FIGURE 1-3

PRODUCT IDENTIFICATION AND FUSE INFORMATION LABEL ...............................1-3

FIGURE 1-4

PRIMARY HAND PENDANT AND FOOTSWITCH CONNECTOR BOX.........................1-3

FIGURE 1-5

PRIMARY HAND PENDANT INDICATORS.........................................................................1-4

FIGURE 1-6

PRIMARY HAND PENDANT FUNCTIONS...........................................................................1-5

FIGURE 1-7

FOOTSWITCH............................................................................................................................1-6

FIGURE 1-8

DEPLOYING FOOT PUMP PEDAL ........................................................................................1-6

FIGURE 1-9

LOCKING FOOT PUMP PEDAL FOR USE...........................................................................1-6

FIGURE 1-10

AUXILIARY HAND PENDANT ...............................................................................................1-7

FIGURE 1-11

LOCATION OF AUXILIARY PENDANT AND DRAWER ..................................................1-7

FIGURE 2-1

PINCH POINTS...........................................................................................................................2-1

FIGURE 2-2

NORMAL TABLE ORIENTATION .........................................................................................2-2

FIGURE 2-3

REVERSE TABLE ORIENTATION ........................................................................................2-2

FIGURE 2-4

NORMAL PERINEAL POSITION ...........................................................................................2-3

FIGURE 2-5

REVERSE PERINEAL POSITION...........................................................................................2-3

FIGURE 2-6

HAND PENDANT POWER-ON INDICATORS......................................................................2-4

FIGURE 2-7

HEADREST .................................................................................................................................2-7

FIGURE 2-8

ALIGNING THE LEG SECTION FOR INSTALLATION ...................................................2-8

FIGURE 2-9

LEG SECTION ............................................................................................................................2-8

FIGURE 2-10

ASSEMBLED LEG SECTION..................................................................................................2-8

FIGURE 2-11

FOOTSWITCH............................................................................................................................2-9

FIGURE 3-1

BACKUP SYSTEMS.................................................................................................................3-10

FIGURE 3-2

AUXILIARY HAND PENDANT .............................................................................................3-10

FIGURE 4-1.

HYDRAULIC POWER UNIT ON MAIN ELEVATING COLUMN .....................................4-1

FIGURE 4-2.

COLUMN MANIFOLD ..............................................................................................................4-2

FIGURE 4-3.

DISTRIBUTION BLOCK...........................................................................................................4-2

FIGURE 4-4.

FLOOR LOCK MANIFOLD .....................................................................................................4-3

FIGURE 4-5.

FOOT LOCK MANIFOLD LOCATION IN BASE.................................................................4-3

FIGURE 4-6.

FLOOR LOCK SYSTEM OPERATION ..................................................................................4-4

FIGURE 4-7.

FLOOR LOCK QUICK DISCONNECT...................................................................................4-5

FIGURE 4-8.

MANIFOLD VALVE ..................................................................................................................4-5

FIGURE 4-9.

COLUMN CYLINDER SCHEMATIC......................................................................................4-7

FIGURE 4-10.

LIFT TUBES/CYLINDERS...................................................................................................4-8

FIGURE 4-11.

TILT CYLINDER AND UPPER LIFT TUBE .....................................................................4-8

FIGURE 4-12.

TILT OPERATION................................................................................................................4-8

FIGURE 4-13.

MANIFOLD AND SOLENOIDS...........................................................................................4-9

FIGURE 4-14.

HOSE ROUTING ...................................................................................................................4-9

FIGURE 4-15.

LEFT SIDE FRAME CYLINDERS....................................................................................4-10

FIGURE 4-16.

RIGHT SIDE FRAME CYLINDERS .................................................................................4-10

Содержание OPERON B 810

























































































































Результаты поиска

Содержание OPERON B 810

Отзывы:

Похожие инструкции для OPERON B 810

Бренды по названию

Популярные бренды

Berchtold OPERON B 810, Запасные части

Результаты поиска

Содержание OPERON B 810

Отзывы:

Похожие инструкции для OPERON B 810

Бренды по названию

Популярные бренды