Bennett CNG Spec. 100 Series Operators Manual
Programming
36
MENU CODE 6 1 – POS TYPE
Menu Code 61 is used to determine the processing type used for POS systems. If the POS has custom handling implemented in the
dispenser’s POS-Dispenser interface then the POS type will be set to that POS otherwise it is left to the standard default.
Note: This mode
only needs to be set if the POS is using Retalix and the CNG is configured as a 1-Sided 2-Hose dispenser.
0 – (Default) Standard
1 – Retalix
TO SELECT A DIFFERENT O PTION IN MENU CODE 61, FOLLOW THIS PROCED URE:
1.
Press the number
6
and 1, then the [
MODE
]
button on the keypad. The PPM display
shows the dispenser is in Menu Code 61. If the dispenser has not been programmed
since it came from the factory, the number 0 appears in the main display. This is the
default setting as shown in
Figure 4.59
.
2.
To change the setting, use
0
or
1
button on the keypad to enter a new option.
Note:
If an error is made, press the correct number. The new number will replace the error.
3.
When the correct option number appears in the main display, press the [
ENTER
]
button to save the selection.
4.
Press the [
CANCEL
] button to exit this Menu Code.
MENU CODE 6 3 – HANDLE MASKING
Menu Code 63 is used to enable or disable handle masking. If a POS will not authorize a dispenser with an active handle this mode will
need to be set to 1. If this mode is set to zero the dispenser will report an activated handle immediately.
0 – (Default) Disable Handle Masking
1 – Enable Handle Masking
TO SELECT A DIFFERENT O PTION IN MENU CODE 63, FOLLOW THIS PROCED URE:
1.
Press the number
6
and
3
, then the [
MODE
]
button on the keypad. The PPM display
shows the dispenser is in Menu Code 61. If the dispenser has not been programmed
since it came from the factory, the number 0 appears in the main display. This is the
default setting as shown in
Figure 4.60
.
2.
To change the setting, use
0
or
1
button on the keypad to enter a new option.
Note:
If an error is made, press the correct number. The new number will replace the error.
3.
When the correct option number appears in the main display, press the [
ENTER
]
button to save the selection.
4.
Press the [
CANCEL
] button to exit this Menu Code.
MENU CODE 65 – MAXIMUM FILL PRESSURE
Menu Code 65 is used to program the maximum fill pressure. The maximum fill pressure (UPT) is the upper limit of the target pressure for
a fill. The default for the pressure limit for the station are based on the grade type (target pressure) assigned in menu code 07. Default
pressure is (P36) 4000 PSI.
TO SELECT A DIFFERENT O PTION IN MENU CODE 65, FOLLOW THIS PROCED URE:
1.
Press the number
6
and
5
, then the [
MODE
]
button on the keypad. The PPM display
shows the dispenser is in Menu Code 65 as shown in
Figure 4.61
. If the dispenser has
not been programmed since it came from the factory, the grade type configured in
menu code 7 appears in the main display. This is the default setting.
2.
To change the setting, use
0
or
1
button on the keypad to enter a new option.
Note:
If an error is made, press the correct number. The new number will replace the error.
3.
When the correct option number appears in the main display, press the [
ENTER
]
button to save the selection.
4.
Press the [
CANCEL
] button to exit this Menu Code.
FIGURE 4.59 – POS TYPE
Sale $
postyp
GGE
std
code
- 61
FIGURE 4.60 – Handle Masking
Sale $
Handle ind
GGE
0
code
- 63
FIGURE 4.61 – MAX FILL PRESSURE
Sale $
upt
GGE
code
- 65
Содержание CNG Spec. 100 Series
