background image

We at Bennett Marine, (Bennett) are committed to product quality and customer 

satisfaction. We’ve supported our products for more than half a century and have earned 

a reputation for exceptional service and support. In keeping with that tradition Bennett 

provides a Limited Warranty for its Products. Please see the table on page 39 for our 

Warranty details. 

Limited Warranty: 

Bennett warrants to the original purchaser and subsequent owners, 

that Bennett will repair or replace, at the discretion of Bennett, any part or component 

manufactured by Bennett which is proven to the satisfaction of Bennett to be defective, and 

which failure has occurred under normal use and within the warranty period. This Limited 

Warranty does not apply to products that have been damaged, or which fail, as a result of 

causes other than manufacturing defects (such as but not limited to electrical overloads, 

electrolysis, casualty, fire, collision, improper installation, lack of maintenance, exposure to 

elements, alteration, or misuse). This warranty does not cover damage to finishes. The warranty 

commences from the first date a product is purchased by the customer. If the product is 

installed on a boat by an OEM then the warranty commences on the first day on which the 

first retail customer purchases the boat. This warranty applies exclusively to products purchased 

and used in the United States. 

Disclaimer And Exclusion Of Warranties:

 This warranty is meant to be a complete 

and exclusive statement of the terms of all express warranties offered by Bennett. To the 

extent permitted by law, there are no warranties, express or implied, including any implied 

warranties of merchantability or fitness for a particular purpose extended by Bennett other 

than the express warranty set forth in this instrument. Some states do not allow the exclusion 

of, or limitations to, implied warranties so the above limitation may not apply to you. 

Warranty Claim Procedure: 

To make a claim please call Bennett Marine at 954-427-1400 

to trouble-shoot the issue and start the claim process. You will be asked to complete a form 

that can be found online at BennettTrimTabs.com/Warranty and return the part for warranty 

evaluation. Parts will be evaluated upon receipt and any part found to meet the above warranty 

criteria will be repaired or replaced at Bennett’s option. Replacement or repaired part will 

be shipped at no cost to customer via ground freight to US destinations only. Any expedite 

methods will be at customers expense. 

Transferability:

 Before expiration of the warranty period, this Limited Warranty is fully 

transferable to subsequent owners of the boat on which it is originally installed and is void if 

the product is removed and reinstalled on another boat or is used for purposes for which it was 

not originally purchased. 

Limitation And Exclusion Of Remedies:

  Bennett’s sole responsibility shall be the repair 

or replacement, at its option, of any defective part or component. In certain instances 

Bennett reserves the right to provide refurbished parts. Customer agrees that this is the 

sole and exclusive remedy under this Limited Warranty. Bennett will not be responsible for 

any incidental, consequential or indirect damages, including loss of use as a result of any 

manufacturing defect in a product. Bennett will not be responsible for labor, haul out, or any 

other fees associated with the removal or installation of warranted part. Some states do not 

allow the exclusion or limitation of incidental or consequential damages, so this limitation 

may not apply to you. 

Bennett Marine Warranty (US Only)

Bennett Marine

  |  Bolt Electric Trim Tab System

38

Содержание BOLT1212









































Отзывы: