background image

26

PP

Selects the operating mode of the ”Step by step button” and of the transmitter.
On: Operation: OPEN > CLOSE > OPEN >
Off: Operation: OPEN > STOP > CLOSE > STOP >

(OFF)

PRE

Enables or disables pre-blinking.
On: Pre-blinking enabled. Blinking is activated 3s before the motor starts.
Off: Pre-blinking disabled.

(OFF)

htr

Enabled or disables HOLD-TO-RUN function
On: HOLD-TO-RUN function.
The pressure of the OPENS/CLOSES button must be maintained throughout the entire manoeuvre. 
The opening of the STOP input stops the motor. All the safety inputs are deactivated.
Off: Automatic/semiautomatic function

(OFF)

ltca

Selects the operating mode of the blinking light during the time TCA
On: Blinking light on during TCA
Off: Blinking light off during TCA

(OFF)

phcl

The operating mode of the PHC input is selected.
On: PHC input is activated in both opening and closing phases.
In the opening phase: the contact opening causes the motor stop. When the photocell is 
released, the motor restarts in the opening phase. In closing phase: the contact opening causes 
the motor stop. When the photocell is released, the motor inverts the movement direction (open).
Off: The PHC input is activated in the closing phase only.
In the closing phase: the contact opening causes the motor stop and the immediate reversion 
of the operation direction (open).

(OFF)

opcl

Enables OPEN input as Pedestrian input (Partial parameter TPED opening).
On: OPEN input enabled as pedestrian input (PED).
Off: No modification to the OPEN input

(OFF)

TST1

Enables or disables checking of photocells on PHOT input, active both in closing and in opening.
On: Check enabled. If the check has a negative result, no manoeuvre is commanded. 
See Fig.23 - “PHOTO TEST”. (AUX1=3)
Off: Check of photocells each time a manoeuvre is disabled. This setting requires maintenance 
of photocells every 6 months.

(OFF)

tst2

Enables or disables the check of photocells on PHC input.
On: Check enabled. If the check fails, no manoeuvre will be enabled. 
See Fig.24 - “PHOTO TEST”. (AUX1=3))
Off: Check of photocells each time a manoeuvre is disabled. This setting requires maintenance 
of photocells every 6 months.

(OFF)

bar

Changing the operating mode of the PHO and BAR inputs in the event the sensitive edges are 
installed on the mobile opening and closure edges (see Fig.21).
On: The PHO input assumes a similar function to the BAR input, but inverts motion for 3s only 
during the opening phase. The edge connected to the BAR input is only active during the clo-
sure phase.
Off: Intervention of the sensitive edge connected to the BAR input stops movement of the door 
and inverts for approx. 3s, both opening and closure. 
The PHO input re-starts functioning of the photocell active on opening.

(OFF)

aopf

The “forced opening in case of power cut-off” function is activated or deactivated (it can be 
activated only with connected and operating emergency batteries). 
On: Activated function. In the event of power failure, before the emergency battery completely 
discharged, the control unit causes an opening operation.
The door remains open until the power supply is back.
Off: Deactivated function.

(OFF)

minv

The opening direction of the motor is selected:
On: Right side motor mount 
Off: Left side motor mount (fig.20)

(OFF)

rem

Enables or disables remote radiotransmitters learning, as indicated in the paragraph “Remote 
transmitters learning”. 
On: Remote learning enabled.
Off: Remote learning not enabled.

(ON)

8.4.3) RADIO (

RADI

)

MENU

FUNZIONE

PP

By selecting this function, the receiver goes in waiting (

Push

) for a transmitter code to assign to the step-step function. 

Press the key of the transmitter to assign to this function. 
If the code is valid, it is memorised and the message 

OK

 is displayed

If the code is not valid, the message 

Err 

is displayed

2Ch

By selecting this function, the receiver goes into waiting (

Push

) for a transmitter code to assign to the second radio channel. 

Press the key of the transmitter to assign to this function. 
If the code is valid, it is memorised ad the 

OK

 message is displayed

If the code is not valid, the message 

Err 

is displayed.

ped

When this function is selected, the receiver awaits (Push) a transmitter code to be assigned to the PED function.
Press the transmitter key, which is to be assigned to this function.
If the code is valid, it will be stored in memory and OK will be displayed.
If the code is not valid, the Err message will be displayed.

ntx

By selecting this function the LCD screen shows the number of transmitters memorized into the receiver.

Содержание BULL 1224 TURBO













































































Отзывы: