manualshive.com logo in svg

Beninca BULL 1224 TURBO, Руководство пользователя, Страница: 24 / 76

Поделиться
Скачать
Beninca BULL 1224 TURBO Скачать руководство пользователя страница 24

24

8) CP.B24 TURBO CONTROL UNIT

8.1) WIRE DIAGRAM

Wire connections shown in Fig. 17 are described hereunder:

M2 SEL. 115V

Mains power supply se-
lection

230Vac 50/60Hz (from 207Vac to 253Vac) M2 OPEN jumper
115Vac 50/60Hz (from 102Vac to 125 Vac) M2 CLOSED jumper

L-N-GND

Mains power supply

Mains power supply input selectable via M2 jumper.

+ BATT -

Batteries 

Input for connecting buffer batteries (accessory) 2x12V 2.1Ah

M11

Motor 

24Vdc motor connection

+ 24 -

24 Vdc

Accessories power supply output 24Vdc 0.8 A max (respect accessories polarity).

AUX1

AUX 1 Auxiliary output

Output with N.O. contact configurable by AUX1 operating logic

BAR J3

Responsive sensor

Responsive sensor contact input
Resistive sensor: Jumper "DAS" closed
Mechanical sensor: Jumper "DAS" open
The sensor stops the movement of the door and reverses it for about 3s.
If the sensor is not used: Jumper "DAS" open, jumper between BAR terminals.

RELEASE SW.

Magnetic Sensor

Input for safety microswitch connected to the release lever. Motor stops IF RELEASE LEVER OPEN. 
All LED segments are on.

S.I.S.

Synchronisation card 
optional

Optional SIS card input for synchronising two opposing automations.
See paragraph synchronisation of two automations.

BLINK

Flashing

24Vdc output 15W max. for connection to the flashing light.

AUX2

Auxiliary output AUX 2

24 Vdc output configurable by AUX2 operating logic (0.5A max)

COM

Common Inputs

Common for all control inputs.

SWO

Limit switch opens

Limit switch input OPENS (N.C. contact).

SWC

Limit switch closes

Limit switch input CLOSES (N.C. contact).

STOP

STOP

Button input STOP (N.C. contact).

PHO

Photocell opening/closing

Input, (N.C. contact) for safety devices (e.g. photocells).
During closure: if the contact is opened, the motor stops. With OPCL logics, when the photocell is 
no longer obscured, the motor reversion occurs (gate opens).
During opening: if the contact is opened, the motor stops. with OPCL logics When the photocell is 
no longer obscured, the motor restarts opening.

PHC

Photocell closing

Input, (N.C. contact) for safety devices (e.g. photocells).
During closure: it can be preset by PHCL logics.
During opening: it can be preset by PHCL logics.

OPEN

Opens

Input for configurable opening command as pedestrian input (N.O. contact)

CLOSE

Closes

Close command input (N.O. contact)

PP

Step-by-step

Step-by-Step button input (N.O. contact)

COM

Common Inputs

Common for all control inputs.

ANT-SHIELD

Antenna

Built-in radio transmitter card antenna connection (ANT-signal/SHIELD-screen).

8.2) PROGRAMMING

The programming of the various functions of the control unit is carried out using the LCD display on the control unit and setting the desired values in 
the programming menus described below.
The parameters menu allows you to assign a numerical value to a function, in the same way as a regulating trimmer.
The logic menu allows you to activate or deactivate a function, in the same way as setting a dip-switch.

8.2.1) TO ACCESS MANUAL PROGRAMMING

1 -Press the <PG> button to enter the first Installation menu “INST”.
2 -Choose with <+> or <-> button the menu you want to select (see menu at page 10-11)
3 - Press the button <PG>, the display shows the first function available on the menu.
4 - With the <+> or <-> button, select the function you want.
5 - Press the button <PG>, the display shows the value currently set for the function selected.
6 - With the <+> or <-> button, select the value you intend to assign to the function.
7 - Press the button <PG>, the display shows the signal “PRG” which indicates that programming has been completed.

8.2.2) PROGRAMMING NOTES

Simultaneously pressing <+> and <-> from inside a function menu allows you to return to the previous menu without making any changes. Hold down 
the <+> key or the <-> key to accelerate the increase/decrease of the values.
Hold down the <+> key or the <-> key to accelerate the increase/decrease of the values.
After waiting 120s the control unit quits programming mode and switches off the display.
When the board is switched on, the software version is displayed for around 5 sec  
The pre-set  logic functions and parameters are made taking account of a typical installation.

Содержание BULL 1224 TURBO













































































Отзывы:

Нет отзывов