Belarus 1021 Скачать руководство пользователя страница 138 | Manualshive

Страница: 138 / 209

background image

BELARUS-1021/1021.3

Operating manual

137

7.9 Troubleshooting of hydraulic linkage system

Trouble, its manifestation

Remedy

1. Hitch without a load does not rise, when any of the control levers of the extension

cylinder distributor is set to the position of lifting or lowering, the characteristic sound
emitted by the pump under load is not heard

Contamination of the safety valve of the

tractor distributor.

Disassemble and rinse the safety valve.

Adjust the pressure maintained by the safety
valve.

2. Hitch without a load does not rise, when any of the control levers of the extension

cylinder distributor is set to the position of lifting or lowering, the characteristic sound
emitted by the pump under load is heard After stopping the position engine, shifting the
lever to the forward position, then to the rear position and starting the engine, the hitch
rises (the power lever must be in the forward position).

Clogged jet hole in the relief valve.

Unmount the regulator distributor from the

tractor, take out the bypass valve, rinse the
valve, clean the jet hole of the valve.

3. Hitch without a load does not rise, when any of the control levers of the extension

cylinder distributor is set to the position of lifting or lowering, the characteristic sound
emitted by the pump under load is heard After stopping the engine, shifting the position
lever to the forward position, then to the rear position and starting the engine, the hitch does
not rise (the power lever must be in the forward position).

Foreign particles under the edges of the

spool.

Remove the cover from the regulator

distributor, set the positional lever in to the
forward position. The spool retaining ring must
rest against the housing of the regulator
distributor. Shift the position lever to the rear
position. The spool must travel up by at least 7
mm. In case of shorter travel, unmount the
regulator distributor, remove the foreign
particles stuck between the edges of the spool
and the housing.

4. Hitch with a load does not rise or rises slowly

Fault manifests itself as the oil in the

hydraulic system warms up — faulty pump.

Check the pump performance. If coefficient

of performance of the pump is less than 0.7 —
replace the pump.

Fault appears at any oil temperature —

clogged relief valve.

Unmount the regulator distributor, take out

the bypass valve, rinse it and the housing in
diesel fuel.

5. Hitch with a load rises slowly, after stopping the engine spontaneously lowers

noticeable to the eye, frequent position correction, possible “freeze” of the pressure.

Destroyed rubber seals of the regulator

distributor.

Unmount the regulator distributor, replace

rubber seals with new ones.

«
...
136
137
138
139
140
...
»

Содержание 1021


















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1021

Бренд: RHINO Страницы: 56

Бренд: Kubota Страницы: 102

Бренд: Kubota Страницы: 115

Бренд: Iseki Страницы: 98

Бренд: Iseki Страницы: 176

Бренд: Winton Страницы: 40

Бренд: LS tractor Страницы: 104

PROXIMA PLUS 90 2012

Бренд: Zetor Страницы: 212

Бренд: Valtra Страницы: 36

5400 BROCHURE 86-112

Бренд: MASSEY FERGUSON Страницы: 13

Reboke 6000 TSI

Бренд: Stara Страницы: 69

Бренд: Buyers Products Company Страницы: 4

Бренд: Kubota Страницы: 74

Бренд: MASSEY FERGUSON Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды