Belanger FLIPPING Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 40

background image

FLIPPING™ ARCH

4

Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL027

Introduction

Important Safety Information

This section introduces the hazard and safety precautions associated with installing, maintaining or
servicing this product. Before performing any task on this product, read this safety information and the
applicable sections in this manual, where additional hazards and safety precautions for your task may
be found. Electrical shock could occur and cause death or serious injury if these safe service
procedures are not followed.

Safety Symbols and Signal Words

Alert Symbol

This safety alert symbol is used in this manual and on warning labels to alert you to
precautions which must be followed to prevent potential personal safety hazards.
Obey safety directives that follow this symbol to avoid possible injury or death.

Signal Words

The signal words used in this manual and on warning labels tell you the seriousness of particular
safety hazards. The precautions that follow must be followed to prevent death, injury or damage
to the equipment.

DANGER

This signal word is used to alert you to a hazard or unsafe practice which WILL RESULT IN

DEATH OR SERIOUS INJURY

This alerts you to a hazard or unsafe practice which COULD RESULT IN DEATH OR

SERIOUS INJURY

CAUTION

This signal word designates a hazard or unsafe practice which MAY RESULT IN MINOR

INJURY

CAUTION

When used by itself, CAUTION designates a hazard or unsafe practice which MAY RESULT IN

PROPERTY OR EQUIPMENT DAMAGE

Before You Begin

Only trained or authorized individuals knowledgeable in the related procedures should install,
inspect, maintain or service this equipment.

Read the Manual

Read, understand and follow this manual and any other labels or related materials supplied with
this equipment. If you do not understand the procedure, call a Belanger, Inc.® representative at
248-349-7010. It is imperative to your safety and the safety of others to understand the
procedures before beginning work

.

«
...
4
5
6
7
8
...
»

Содержание FLIPPING









































Отзывы:

Нет отзывов

Похожие инструкции для FLIPPING

Бренд: National Страницы: 44

Бренд: HAGOR Страницы: 12

Бренд: Hahn Страницы: 2

Бренд: HAGOR Страницы: 16

Бренд: Viking Страницы: 1

WHITEBOX SOLUTIONS 1 U

Бренд: Lanner Страницы: 2

Бренд: Yakima Страницы: 30

Бренд: ricoo Страницы: 2

CONCEPT HOUSWARES PR-40322

Бренд: PR Housewares Страницы: 2

Бренд: Premier Mounts Страницы: 2

Бренд: Daewoo Страницы: 6

Бренд: TYAN Страницы: 180

Бренд: Troyer's Birds' Paradise Страницы: 10

Бренд: Konig & Meyer Страницы: 8

Charisma SEG XSS Custom Adjustable Series

Бренд: Testrite Visual Страницы: 2

Бренд: Mount Plus Страницы: 2

Бренд: Rompa Страницы: 8

Бренд: Sealey Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды