background image

FLIPPING™ ARCH

                                                                

 

2     

Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

       

1MANUL027

 

 

Belanger Incorporated® Limited Warranty 

LIMITED WARRANTY:  

 
Equipment: 

 

Subject to the limitations stated below, Seller warrants that the Equipment sold hereunder, which is fabricated by Seller, 
shall  be  free  from  defects  in  workmanship  and  material  under  normal  use  and  service  for  a  period  of  1  year  plus  30 
days from the date of invoice - CAT

 Pumps will be warranted for 2 years from the date of invoice. 

 
Parts: 

 

Subject  to  the  limitations  stated  below,  Seller  warrants  that  the  Parts  sold  hereunder,  shall  be  free  from  defects  in 
workmanship and material under normal use and service for a period of 30 days from the date of invoice.   
 
Limitations on All Warranties: 

 

The  warranties  contained  in  this  Section  13  are  subject  to  the  following  limitations:  (1)  they  are  void  if  the  factory 
specifications  for  operation  and  maintenance,  found  in  original  equipment  manuals,  and  component  manuals,  are not 
followed, or if other than factory authorized erection, alterations or modifications are made to any Parts or Equipment; 
(2) defective Parts are warranted to the Purchaser only for repair or replacement through an authorized Purchaser or 
Distributor  of  Seller,  or  direct  with  Seller  for  a  period  of  13  months  from  the  date  of  invoice;  however,  this  warranty 
excludes  all  claims  for failure resulting from normal wear and tear, improper installation, omission of factory specified 
preventative  maintenance,  misuse,  abuse,  negligence,  third  party  damages,  or  acts  of  God  and  Purchaser  agrees  to 
submit to and assist Seller or its authorized Purchaser or Distributor in conducting in-warranty inspections of the Goods 
including inspection of any Equipment or Parts claimed to be defective by the Purchaser; (3) the cost of providing  labor 
or repair to replace Equipment and Parts warranted to Purchaser will be included within the warranty only if such claim 
is  made  within  120  days  from  the  date  of  invoice  and  then  only  during  normal  business  hours  through  an  authorized 
Purchaser  or  Distributor  of  Seller,  or  direct  with  Seller,  and    labor  and  service  provided  beyond  the  labor  warranty 
period  shall  be  subject  to  labor  charges  at  the  rates  established  by  the  local  authorized  Purchaser  or  Distributor  or 
direct with Seller; (4) the warranties shall be void for all Equipment failures and premature Part wear caused by the use 
of corrosive chemicals in the wash process, and the following list includes some, but not all, of the particularly corros ive 
chemicals  that  if  used  in  conjunction  with  Equipment  or  Parts  will  void  the  warranty:    Hydrofluoric  Acid,  Ammonium 
Bifluoride,  Bromic  Acid,  Muriatic  Acid,  Sulfonic  Acid,  Phosphoric  Acid,  Hydrogen  Cyanide,  Hydrochloric  Acid,  Sodium 
Hydroxide  and  Chlorinated  Solvents;  (5)  Seller  makes  no  warranty,  express  or  implied,  with  respect  to  the  design  or 
operation  of  any  entire  system,  in  which  Seller’s  Equipment  or  Parts  sold  hereunder  are  mere  components;(6)  in  no 
event shall Seller be liable for any incidental, special, consequential, punitive or exemplary damages resulting from the 
furnishing,  performance  or  use  of  any  Goods  or  services  sold  pursuant  hereto,  whether  due  to  a  breach  of  contract, 
breach  of  warranty,  negligence  or  any  other claim at law or equity.  Seller shall not be liable for any damages of any 
kind,  including,  but  not  limited  to,  loss  of  business;  inconvenience,  or  property  damage  of  any  kind;  nor  for  any 
damages  of  whatever  nature  resulting  in  any  way  from  the  Purchaser’s  selection  and  use  of  any  chemicals  not 
manufactured  exclusively  by  Seller  but  used  with  the  purchased  Equipment or Parts; or for any service not expressly 
provided herein related to or arising from the Equipment or Parts sold. Seller shall not be liable for damages resulting 
from Purchaser’s use of any engineering recommendations, sales representations, technical assistance, advice or data 
other than that information contained in Belanger manuals; (7) all warranties, express, implied, or statutory, pertaining 
to the Equipment and Parts apply to the  Purchaser only; are not transferable; are fully set forth herein; and no addition 
to  or  modification  thereto  shall  be  binding  upon  the  Seller,  unless  made  in  writing  and  signed  by  a  duly  authorized 
employee of Seller.  
 
No Other Warranties:   

 

THIS LIMITED WARRANTY FOR EQUIPMENT AND PARTS IS EXPRESSLY IN LIEU OF ALL OTHER 
WARRANTIES, EXPRESS OR IMPLIED, WHETHER STATUTORY OR OTHERWISE, INCLUDING ANY 
IMPLIED WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR 
PURPOSE.  THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR 
PURPOSE CONTAINED IN THE UNIFORM COMMERCIAL CODE – SALES ARE EXPRESSLY 
DISCLAIMED. 

 

Copyright  ©2013 by Belanger, Inc. All rights reserved.  No part of this work may be reproduced or transmitted in any 
form or by any means, electronic or mechanical, including photocopying and recording, or by any information storage or 
retrieval  system,  except  as  may  be  expressly  permitted  by  the  1976  Copyright  Act.  Belanger  reserves  the  right  to 
change or modify the Belanger Inc. Limited warranty without notice. 

Содержание FLIPPING









































Отзывы: