Beckhoff ELX3202 Скачать руководство пользователя

Страница: 3 / 72

Table of contents

ELX3202 and ELX3204

Version: 1.4.0

Table of contents

1 Foreword .................................................................................................................................................... 5

1.1

Notes on the documentation........................................................................................................... 5

1.2

Safety instructions .......................................................................................................................... 6

1.3

Documentation Issue Status........................................................................................................... 7

1.4

Marking of ELX terminals................................................................................................................ 8

2 Product overview..................................................................................................................................... 12

2.1

ELX3202 - Introduction ................................................................................................................. 12

2.2

ELX3204 - Introduction ................................................................................................................. 13

2.3

Technical data .............................................................................................................................. 14

2.4

Intended use ................................................................................................................................. 15

3 Mounting and wiring ............................................................................................................................... 16

3.1

Special conditions of use for ELX terminals ................................................................................. 16

3.2

Installation notes for ELX terminals .............................................................................................. 16

3.3

Arrangement of ELX terminals within a bus terminal block .......................................................... 18

3.4

Installation position and minimum distances ................................................................................ 21

3.5

Installation of ELX terminals on mounting rails............................................................................. 22

3.6

Connection.................................................................................................................................... 23
3.6.1

Connection system........................................................................................................... 23

3.6.2

Wiring ............................................................................................................................... 24

3.6.3

Proper line connection ..................................................................................................... 25

3.6.4

Shielding and potential separation ................................................................................... 25

3.6.5

ELX3202 - Contact assignment ....................................................................................... 26

3.6.6

ELX3204 - Contact assignment ....................................................................................... 28

4 Basic function principles........................................................................................................................ 30

4.1

EtherCAT basics ........................................................................................................................... 30

4.2

Notices on analog specifications .................................................................................................. 30
4.2.1

Full scale value (FSV) ...................................................................................................... 30

4.2.2

Measuring error/ measurement deviation ........................................................................ 30

4.2.3

Temperature coefficient tK [ppm/K] ................................................................................. 31

4.2.4

Single-ended/differential typification ................................................................................ 32

4.2.5

Common-mode voltage and reference ground (based on differential inputs) .................. 35

4.2.6

Dielectric strength ............................................................................................................ 35

4.2.7

Temporal aspects of analog/digital conversion ................................................................ 36

5 Parameterization and programming ...................................................................................................... 40

5.1

Settings and application notes...................................................................................................... 40
5.1.1

Default settings ................................................................................................................ 40

5.1.2

Changing the slave parameters in the CoE directory ...................................................... 40

5.1.3

Disabling of channels ....................................................................................................... 41

5.1.4

Programmed characteristic sensor curves....................................................................... 42

5.2

Process data and operating modes .............................................................................................. 43
5.2.1

Data flow .......................................................................................................................... 43

5.2.2

Sync Manager (SM) ......................................................................................................... 43

5.2.3

Operating modes and settings ......................................................................................... 43

5.2.4

Influence by interfering devices ....................................................................................... 47

5.3

TwinSAFE SC ............................................................................................................................... 47
5.3.1

TwinSAFE SC - operating principle ................................................................................. 47

5.3.2

TwinSAFE SC - configuration .......................................................................................... 48

Содержание ELX3202









































































Результаты поиска

Содержание ELX3202

Отзывы:

Похожие инструкции для ELX3202

Бренды по названию

Популярные бренды

Beckhoff ELX3202, Руководство по эксплуатации

Результаты поиска

Содержание ELX3202

Отзывы:

Похожие инструкции для ELX3202

Бренды по названию

Популярные бренды