Beckhoff ELX3202 Скачать руководство пользователя

Страница: 40 / 72

Parameterization and programming

ELX3202 and ELX3204

Version: 1.4.0

Parameterization and programming

5.1

Settings and application notes

5.1.1

Default settings

The EL320x can be used for direct temperature or resistance measurements. The corresponding CoE
settings are shown in the following table.

The relationship between temperature and resistance of a Pt100/Pt1000 sensor is shown below:

Temperature

typical resistance, approx.

850°C

Pt1000: 3.9 kΩ

Pt100: 390 Ω

320°C

Pt1000: 2.2 kΩ

Pt100: 220 Ω

-200°C

Pt1000: 180 Ω

Pt100: 18 Ω

Characteristic sensor curves are available from the sensor manufacturers.

You can obtain further information in the chapters

Object description and parameterization [

}

53]

and

Process data and operating modes.

ELX3202

ELX3204

Default/
factory setting

• 4-wire connection

• Pt100 (CoE 0x80n0:19)

• Presentation signed (CoE 0x80n0:02)

• Limits disabled

• All channels enabled

• 2-wire connection

• Pt100 (CoE 0x80n0:19)

• Presentation signed (CoE 0x80n0:02)

• Limits disabled

• All channels enabled

Notice regarding Resistance Measurement mode

In Resistance Measurement mode the measured value is always displayed unsigned, irrespective of the
Presentation setting (object

0x80n0:02 [

}

53]

), as 0...xFFFF with the respective value.

1/16 Ω -> ~62 mΩ/Digit

1/64 Ω -> ~15 mΩ/Digit

5.1.2

Changing the slave parameters in the CoE directory

During commissioning it may be necessary to change the CoE parameters.

• If the terminal is accessed online, the CoE directory is read from the slave and can be changed, see

fig.

Accessing the CoE parameters in the TwinCAT System Manager

• If the terminal is accessed offline (the terminal is then not addressable) the data from the XML

description is used. The parameters cannot be changed.

The CoE parameters (CAN over EtherCAT) can be changed in the

CoE-Online

tab of the EtherCAT slave.

Содержание ELX3202









































































Результаты поиска

Содержание ELX3202

Отзывы:

Похожие инструкции для ELX3202

Бренды по названию

Популярные бренды

Beckhoff ELX3202, Руководство по эксплуатации

Результаты поиска

Содержание ELX3202

Отзывы:

Похожие инструкции для ELX3202

Бренды по названию

Популярные бренды