Beckhoff ELX3202 Скачать руководство пользователя

Страница: 55 / 72

Parameterization and programming

ELX3202 and ELX3204

Version: 1.4.0

Index
(hex)

Name

Meaning

Data type

Flags

Default

80n0:19

RTD element

RTD element:

dec

: Pt100 (default)

dec

: Ni100, -60°C to 250°C

dec

:Pt1000, -200°C to 850°C

dec

: Pt500, -200°C to 850°C

dec

: Pt200, -200°C to 850°C

dec

: Ni1000, -60°C to 250°C

dec

: Ni1000, 100°C: 1500 Ω (-30 to 160°C)

dec

: Ni120, -60°C to 320°C

dec

: Output in Ohm, Resolution 1/16 Ω (0 to 4095 Ω)

dec

: Output in Ohm, Resolution 1/64 Ω (0 to 1047 Ω)

dec

: KT100/110/130/210/230 KTY10/11/13/16/19

dec

: KTY81/82-110,120,150 (-50...150°C)

dec

: KTY81-121

dec

: KTY81-122

dec

: KTY81-151

dec

: KTY81-152

dec

: KTY81/82-210,220,250

dec

: KTY81-221

dec

: KTY81-222

dec

: KTY81-251

dec

: KTY81-252

dec

: KTY83-110,120,150 (-50...175°C)

dec

: KTY83-121

dec

: KTY83-122

dec

: KTY83-151

dec

: KTY83-152

dec

: KTY84-130,150 (-40...300°C)

dec

: KTY84-151

dec

: KTY21/23-6 (-50...150°C)

dec

: KTY1x-5

dec

: KTY1x-7

dec

: KTY21/23-5

dec

: KTY21/23-7

UINT16

0x0000 (0

dec

)

80n0:1A

Connection technol-
ogy

Connection technology:

0: Two-wire connection
1*: Three-wire connection
2*: Four-wire connection
3: not connected

UINT16

0x0000 (0

dec

)

80n0:1B

Wire calibration 1/32
Ohm

Calibration of the supply lines

INT16

0x0000 (0

dec

)

*) not for ELX3204

Index 8040: TSC Settings (only ELX320x-0090)

Index
(hex)

Name

Meaning

Data type

Flags

Default

8040:0

TSC Settings [

}

48]

Max. ubindex

UINT8

0x02 (2

dec

)

8040:01

Address

TwinSAFE SC Address

UINT16

0x0000 (0

dec

)

8040:02

Connection Mode

Selection of TwinSAFE SC CRC

UINT32

0x00000000 (0

dec

)

5.4.2

Standard objects (Index 0x1000 … 0x1FFF)

The standard objects have the same meaning for all EtherCAT slaves.

Index 1000: Device type

Index (hex) Name

Meaning

Data type

Flags

Default

1000

Device type

Device type of the EtherCAT slave: the Lo-Word contains
the CoE profile used (5001). The Hi-Word contains the
module profile according to the modular device profile.

UINT32

( )

Index 1008: Device name

Index (hex) Name

Meaning

Data type

Flags

Default

1008

Device name

Device name of the EtherCAT slave

STRING

( )

Содержание ELX3202









































































Результаты поиска

Содержание ELX3202

Отзывы:

Похожие инструкции для ELX3202

Бренды по названию

Популярные бренды

Beckhoff ELX3202, Руководство по эксплуатации

Результаты поиска

Содержание ELX3202

Отзывы:

Похожие инструкции для ELX3202

Бренды по названию

Популярные бренды