Beckhoff ELX3202 страница 22 Скачать руководство пользователя | Manualshive

Страница: 22 / 72

background image

Mounting and wiring

ELX3202 and ELX3204

22

Version: 1.4.0

3.5

Installation of ELX terminals on mounting rails

WARNING

Risk of electric shock and damage of device!

Bring the bus terminal system into a safe, powered down state before starting installation,
disassembly or wiring of the bus terminals!

CAUTION

Danger of injury due to power contacts!

For your own protection, pay attention to careful and careful handling of the ELX terminals.
In particular, the left side mounted, sharp-edged blade contacts pose a potential risk of in-
jury.

Assembly

Fig. 15: Attaching on mounting rail

The bus coupler and bus terminals are attached to commercially available 35 mm mounting rails (DIN rails
according to EN 60715) by applying slight pressure:

1. First attach the fieldbus coupler to the mounting rail.

2. The bus terminals are now attached on the right-hand side of the fieldbus coupler. Join the compo-

nents with tongue and groove and push the terminals against the mounting rail, until the lock clicks
onto the mounting rail.
If the terminals are clipped onto the mounting rail first and then pushed together without tongue and
groove, the connection will not be operational! When correctly assembled, no significant gap should
be visible between the housings.

Note

Fixing of mounting rails

The locking mechanism of the terminals and couplers extends to the profile of the mounting
rail. At the installation, the locking mechanism of the components must not come into con-
flict with the fixing bolts of the mounting rail. To mount the mounting rails with a height of
7.5 mm under the terminals and couplers, you should use flat mounting connections (e.g.
countersunk screws or blind rivets).

«
...
20
21
22
23
24
...
»

Содержание ELX3202









































































Отзывы:

Нет отзывов

Похожие инструкции для ELX3202

Бренд: O&K Antriebstechnik Страницы: 118

Бренд: Veichi Страницы: 40

Бренд: WPT POWER Страницы: 9

Бренд: D+H Страницы: 24

Бренд: Carotron Страницы: 42

Бренд: LG Страницы: 16

Бренд: LG Страницы: 2

Бренд: LG Страницы: 2

Бренд: LG Страницы: 2

Бренд: LG Страницы: 14

Бренд: LG Страницы: 2

GSA-E40L - Super-Multi

Бренд: LG Страницы: 4

Бренд: LG Страницы: 4

GSA-E50L - Super-Multi

Бренд: LG Страницы: 4

Бренд: LG Страницы: 2

Бренд: LG Страницы: 2

Бренд: LG Страницы: 4

Бренд: LG Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды