manualshive.com logo in svg

Beckhoff ELX3202, Руководство по эксплуатации

Поделиться
Скачать
Beckhoff ELX3202 Скачать руководство пользователя страница 41

Parameterization and programming

ELX3202 and ELX3204

41

Version: 1.4.0

Fig. 29: ELX3202 - Accessing the CoE parameters in TwinCAT

Attention

Changes in the CoE directory, in the case of exchange

So that, in the case of exchanging an EtherCAT slave, the CoE parameters are set cor-
rectly in the new slave, changes on the customer side must be entered in the start-up list.

Note

Changes in the CoE directory, program access

The CoE parameters can also be read and written during operation (insofar as it makes
sense) by the PLC using corresponding control commands. For details, see the corre-
sponding articles in the Beckhoff Information System, for example.

The CoE parameters should be written in the status 

PreOperational

 or 

SafeOperational

 and

then the slave should be switched to the status 

Operational

!

For detailed information on settings and operating modes, please read the chapter Process data and
operating modes.

5.1.3

Disabling of channels

Note

Connection technology setting

Besides 2, 3 and 4-wire connection*, 

not connected

 can also be selected for each channel.

The channel concerned is completely disabled and the conversion time of the EL320x is
correspondingly shortened.

*) 3- and 4-wire not valid for ELX3204

Содержание ELX3202









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды