Beastx Aircraft Скачать руководство пользователя страница 77

Страница: 77 / 88

Description

Reason

Solutions

The MICRObeAST does

not initialize .

The Status-LED is flashing red.

The MICROBEAST

signals a sensor

failure

- Helicopter must stand absolutely still

during initialization process.

- Strong wind can shake the helicopter and

therefore the sensors. Lay it on the side

during the initialization.

- Don’t initialize on a vibrating support, like

a car hood or trunk with a running motor.

Turn off the motor!

- Sensors are damaged.

Return MICROBEAST for repair

The Menu LEDs

are

running up and down,

MICROBEAST does not

initialize.

The MICROBEAST

has no valid

signal from the

receiver.

- Check the wiring. Mainly check receiver

wires for polarity on both sides and correct

plugging (no vertical offset by one pin)

- In case of 2.4GHz, check the transmitter-

receiver binding.

- Check the correct receiver type is set,

chapter 5.

12. TROUBLE SHOOTING

Содержание Aircraft

























































































Результаты поиска

Содержание Aircraft

Отзывы:

Бренды по названию

Популярные бренды

Beastx Aircraft, Инструкция по эксплуатации

Результаты поиска

Содержание Aircraft

Отзывы:

Бренды по названию

Популярные бренды