manualshive.com logo in svg

Beastx Aircraft, Инструкция по эксплуатации

Поделиться
Скачать
Beastx Aircraft Скачать руководство пользователя страница 39

39 

The MICROBEAST can be used with nearly all available servo types. However, the selected servos should 
be adequate for flybarless operation (high torque and also fast and precise).

The quality of the servos will have a direct influence on the range of rotor blades that can be used. The 
more the servos are suited for flybarless operation, the less important is the flybarless specificity of the 
rotor blades. 

The use of a bad servo-rotor blade combination will lead to several issues, ranging from oscillations du-
ring hover to unwanted reactions in fast forward flight.

To select the desired servo frequency, move the tail stick repeatedly in one direction until the Status-LED 

lights in the correct color. 

 

The option “

user defined

” allows you to define your own setting with the PC software.

Push the button to save the configuration and to proceed to setup menu point 

C

 .

Содержание Aircraft

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды