Beastx Aircraft Скачать руководство пользователя страница 25

Страница: 25 / 88

Then press the button, but only

briefly,

to save the setup and switch to receiver menu point

If you have already briefly pressed the button by mistake and it did not change the receiver type but switch

to menu point B, switch off the power and repeat the above procedure.

Programming example -

operation with a Futaba® S-Bus receiver:

Hold the button down

Release button

Turn Power

supply ON

Keep button

pushed

long

time

Keep button

pushed

long

time

push button

shortly

LED

: flashing

Status-LED: OFF =

Standard receiver

LED

: flashing

Status-LED:

flashing red

Futaba® S-Bus receiver

LED

: flashing

Status-LED:

purple

Spektrum® receiver

LED

: flashing

Status-LED:

blue

as soon as signal is valid

Menu Point

Fig. 11

convention:

LED lights: LED is flashing:

Note:

If selected receiver type is “Standard” the set up is now complete and by briefly pushing the

button you will jump directly to the end of adjustment procedure (all menu LEDs are flashing).

Switch off the power supply now.

Another channel assignment is not necessary and not provided since the allocation takes place by

appropriate insertion of the cables into the “standard” receiver. So you can directly proceed with

chapter 6.

Содержание Aircraft

























































































Результаты поиска

Содержание Aircraft

Отзывы:

Бренды по названию

Популярные бренды

Beastx Aircraft, Инструкция по эксплуатации

Результаты поиска

Содержание Aircraft

Отзывы:

Бренды по названию

Популярные бренды