manualshive.com logo in svg

Beastx Aircraft, Инструкция по эксплуатации

Поделиться
Скачать
Beastx Aircraft Скачать руководство пользователя страница 68

68 

D

 Tail HeadingLock gain

At parameter menu point 

D

 the HeadingLock gain for the tail can be adjusted:

The HeadingLock gain determines how constant the tail will maintain the rotation rate predetermined 

by the stick (this includes a rotation rate of height 0 = stick center position). Start with the  HeadingLock 

gain set to low or very low and find out the highest possible tail gain in your transmitter. Then you can 

start to increase the HeadingLock gain: 

•  If  the  HeadingLock  gain  is  too  low,  pirouettes  will  be  inconsistent  during  fast  forward  flight  or  in 

crosswind conditions.

• Is the HeadingLock gain too high, it can happen that fast tail-direction changes no longer can be 

controlled clean. It is also possible that the tail will commute gently while hovering or flying around  

(which also often can be a sign of a stiff tail mechanics!) and bounce back when stopping the rotation. 

Was the appropriate setting determined it is usually necessary to adjust the tail gyro gain in the 

transmitter again.

Move the tail stick into one direction until the Status-LED lights in the desired color: 

Status-LeD

Tail HeadingLock gain

purple

very low

red 

flashing

low

red

medium *

blue 

flashing

high

blue

very high

off

user defined

*

 Factory Setting

Содержание Aircraft

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды