Beastx Aircraft Скачать руководство пользователя страница 55

Страница: 55 / 88

Setting the swashplate sensor directions

At setup menu point

, you check if the sensors for aileron and elevator are working in the correct direction.

This can be directly verified in this menu point: If you roll or tilt the helicopter by hand the swashplate has to steer

against this movement. Please refer to this on the next pages Fig. 30 and 31.

If this is not correct, you can reverse the sensor directions by moving the tail stick in one direction. For

confirmation you will see that the Status-LED changes color. Repeat this step until both sensors are

correcting in the correct direction.

There are four possible displays for control to choose from, one will be correct:

Push the button to save the configuration and to proceed to setup menu point

When tilting the helicopter forward the swashplate has to move backwards, when tilting the heli-

copter to the back, the swashplate has to compensate forward. Same thing applies to the roll axis,

when you roll the helicopter to the left the swashplate has to steer right and vice versa. Basically the

swashplate has to remain horizontal while banking the helicopter.

Sensor direction

Status-LeD

elevator

Aileron

off

reversed

purple

reversed

normal

red

normal

reversed

blue

normal*

Factory Setting

Содержание Aircraft

























































































Результаты поиска

Содержание Aircraft

Отзывы:

Бренды по названию

Популярные бренды

Beastx Aircraft, Инструкция по эксплуатации

Результаты поиска

Содержание Aircraft

Отзывы:

Бренды по названию

Популярные бренды