Beastx Aircraft Скачать руководство пользователя страница 22

Страница: 22 / 88

4 .2 .3 Connecting single line receivers without additional servo outputs

(e .g . PPM composite signal receivers)

For the connection of PPM composite signal receivers there is usually no special adapter required. In

most cases (e.g. Futaba ®-receivers of the SP-series) the receiver can be connected to the MICROBEAST

with one of the supplied regular 3-wire cables. For some receivers, the connecting cable is also already

fixed to the receiver (e.g. Jeti ® satellite receiver).

If not fixed to the receiver, plug the cable into the output of the digital composite signal of your receiver,

usually labeled with “SIG” or the like. Again pay attention to correct polarity. Be careful, since the sup-

plied cable is designed to be used “universally”, and the usual Futaba® polarity protection tab is mis-

sing.

Plug the other end of the cable into the MICROBEAST input

[DI1]

. Make sure the polarity is correct; the

orange signal line must be next to the MICROBEAST top cover.

Fig. 9

Top

CH5 throttle servo/ESC and power supply

Elevator servo

Aileron servo

Aileron/pitch servo

Tail servo

Power supply

CH6 additional channel

PPM composite

signal Receiver

Содержание Aircraft

























































































Результаты поиска

Содержание Aircraft

Отзывы:

Бренды по названию

Популярные бренды

Beastx Aircraft, Инструкция по эксплуатации

Результаты поиска

Содержание Aircraft

Отзывы:

Бренды по названию

Популярные бренды