Beastx Aircraft Скачать руководство пользователя страница 63

Страница: 63 / 88

9. pARAMETER MENU

When the MICROBEAST is ready, hold down the button until the Menu LED next to point

flashes

quickly and then release the button. This is how to enter the

parameter menu

To switch to the next parameter menu point, just briefly press the button once again. After the last

menu point pressing the button one time more exits the parameter menu and the MICROBEAST is

ready for flight again. Status-LED will indicate the tail gyro mode and the LEDs

are off.

Single menu points can be skipped without performing any changes. Therefore don‘t move any stick

while you are at the menu point you want to skip and just press the button shortly once again. The

parameter menu has only eight points

, after point

you exit the parameter menu and the

MICROBEAST returns to flight mode.

Never attempt to fly when the MICRObeAST is in one of the menus!

In this condition the control system and sometimes the stick inputs are deactivated!

Содержание Aircraft

























































































Результаты поиска

Содержание Aircraft

Отзывы:

Бренды по названию

Популярные бренды

Beastx Aircraft, Инструкция по эксплуатации

Результаты поиска

Содержание Aircraft

Отзывы:

Бренды по названию

Популярные бренды