Beastx Aircraft Скачать руководство пользователя страница 20

Страница: 20 / 88

binding procedure

In the case of using a Spektrum® satellite receiver it is very important to bind the receiver first

before programming the MICROBEAST.

This step is essential to perform

, even if the satellite was

already in use elsewhere (e. g. in connection with a “standard” Spektrum® receiver) and was already

bound to the transmitter earlier.

To bind a satellite receiver, it must be connected via the adapter to the MICROBEAST.

Simultaneously with the binding process, the type of satellite receiver has to be set, i .e .

whether it is a DSMX or DSM2 satellite (The actual selected signal protocol in the transmitter

is not relevant!) . It is very important to choose the correct type of satellite receiver here,

since an improper setting may seem to work but can lead to radio interference or total loss

of the link in the subsequent operation!

Insert a Spektrum® “Bind Plug” in the [SYS] slot on MICROBEAST.

In cases where power is supplied exclusively by the [SYS] Connection, to bind a Spektrum® satellite re-

ceiver, the power supply must be provided temporarily through any of the servo port (CH1 - CH5).
To select a

DSM2

satellite and to enter bind mode, simply switch on the power supply now. The

LED on the receiver and LED

on the MICROBEAST will start to flash. You can bind the transmitter

as usual (for more information refer to the instructions of your radio control system).
To select and bind a

DSMX

satellite, hold down the button on the MICROBEAST while switching

on the power supply. Now the receiver‘s LED and LED

(!) on the MICROBEAST will flash and you

can release the button and bind the receiver with your transmitter.
After successful binding procedure the receiver‘s LED will stay solid. LED

respectively

flash

alternately to all other LEDs. Now switch off the power supply and remove the bind plug. Now

continue with receiver type setup (see next chapter).

Note: It makes no difference if you pull off the “Bind Plug” during the binding process or leave it

connected as you would expect from some “

standard”

Spektrum

® receivers.

Watch out that the motor can not start accidentally when using the beC of your speed controller

to power the unit!

Содержание Aircraft

























































































Результаты поиска

Содержание Aircraft

Отзывы:

Бренды по названию

Популярные бренды

Beastx Aircraft, Инструкция по эксплуатации

Результаты поиска

Содержание Aircraft

Отзывы:

Бренды по названию

Популярные бренды