Baumuller BM5-O-SAF-002 Скачать руководство пользователя страница 42

Страница: 42 / 182

Processing and Display Elements

Operation Manual

Safety Module for b maXX 5000

BM5-O-SAF-002/3

Document no.: 5.11016.03

Baumüller Nürnberg GmbH

of 180

7.7

Processing and Display Elements

7.7.1

LEDs for the Display of Operating States

For the display of the operating status the Safety Module has two LEDs on the front side
(LED H1 - red, LED H2 - green).

LED H1 (red) - Display of errors or incompatibility to the controller.

LED H2 (green) - Display of an error-free operation.

Figure 10:

LEDs Safety Module

In the following table the possible display combinations of the status-LEDs and its
meaning are listed:

LEDs

H1 (red)

H2 (green)

Meaning

Off

No supply voltage

Off

Error-free operation.

Содержание BM5-O-SAF-002























































































































































































Результаты поиска

Содержание BM5-O-SAF-002

Отзывы:

Бренды по названию

Популярные бренды

Baumuller BM5-O-SAF-002, Руководство по эксплуатации

Результаты поиска

Содержание BM5-O-SAF-002

Отзывы:

Бренды по названию

Популярные бренды