manualshive.com logo in svg

Baumer GIM500R, Руководство пользователя

Поделиться
Скачать
Baumer GIM500R Скачать руководство пользователя страница 3

 

 

Baumer_GIM500R_CANopen_MA_EN.docx

 

3/29 

www.baumer.com 

03.19  

Disclaimer of liability 

The present manual was compiled with utmost care, errors and omissions reserved. For this reason 
Baumer rejects any liability for the information compiled in the present manual. 
Baumer nor the author will accept any liability for direct or indirect damages resulting from the use of the 
present information. 
 
At any time we should be pleased receiving your comments and proposals for further improvement of the 
present manual. 
 
Created by: 
Baumer IVO GmbH & Co. KG 
Villingen-Schwenningen, Germany 

 
 
 

1 

Introduction 

1.1 

Scope of delivery 

Please check the delivery upon completeness prior to commissioning. 
Depending on sensor configuration and part number delivery is including: 

  Sensor 

  Describing file and manual (also available as download in the Internet) 

 
 

1.2 

Product assignment 

 

Product 

Product 
code 

Measuring  
direction 

Device 
name 

EDS file 

GIM500R 

0x40 

1-dimensional  GIM500 

160502_GIM500R_V1_00_PDO_SPEC_1_1dimensional 

GIM500R 

0x40 

2-dimensional  GIM500 

160502_GIM500R_V1_00_PDO_SPEC_1_2dimensional 

 
 

 

Содержание GIM500R






























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды