Baumer GIM500R Скачать руководство пользователя страница 24

Страница: 24 / 29

Baumer_GIM500R_CANopen_MA_EN.docx

24/29

www.baumer.com

03.19

3.4.2.1

Baud rate (2100h)

The baud rate can be changed and read through this object (Additionally to LSS). The following parameters
are possible:

Baud rate (2100h)

Value

Description

50kBaud

100kBaud

125kBaud

250kBaud

500kBaud

800kBaud

1000kBaud

The new baud rate will take effect after a restart. 10kBaud is not supported.

3.4.2.2

Node-ID (2101h)

The Node-ID can be changed and read through this object (Additionally to LSS). The parameters are possible:

Node-ID (2101h)

Value

Description

1..127

Node-ID

The new Node-ID will take effect after a restart.

3.4.2.3

Axis Alignment (2106h)

By accessing this object a change of the device orientation can be done (swapping sign and switch axes). A
change of the default orientation can lead to a loss of accuracy and is not suggested.

Axis mapping (subindex 1)

The axes can be switched as shown in the following tables:

Bit Mask:

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Reserved

Mapped Z Axis

Mapped Y Axis

Mapped X Axis

Default

Possible values:

Value (bit) Axis
00

X-Axis

Y-Axis

Z-Axis

Invalid

Axis sign (subindex 2)

Bit Mask:

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Reserved

Z-Axis

Y-Axis

X-Axis

Default

Possible values:

Value (bit)

Sign

Positive

Negative

Содержание GIM500R






























Результаты поиска

Содержание GIM500R

Отзывы:

Бренды по названию

Популярные бренды

Baumer GIM500R, Руководство пользователя

Результаты поиска

Содержание GIM500R

Отзывы:

Бренды по названию

Популярные бренды