Baumer GIM500R Скачать руководство пользователя страница 28

Страница: 28 / 29

Baumer_GIM500R_CANopen_MA_EN.docx

28/29

www.baumer.com

03.19

3.5

LED status display

The LED status display is according to DS-303 Part 3 V1.0.0 with some exceptions. The following defined
LED behaviors are overwritten by the application in case of a severe internal error.

3.5.1

CANopen Status LED (Green)

Status LED

State

Description

Single flash

STOPPED

The Device is in STOPPED state

Blinking

PREOPERATIONAL

The Device is in the PRE-
OPERATIONAL state

OPERATIONAL

The Device is in the
OPERATIONAL state

Off

Power off

The Device is not powered

3.5.2

CANopen Error LED (Red)

Error LED

State

Description

Single flash

Bus warning

The CAN controller is not
receiving ACK messages (i.e. no
master)

Off

No error

The Device is in working
condition

Bus off / Internal Error

The CAN controller is bus off or
an internal error is present.

Содержание GIM500R






























Результаты поиска

Содержание GIM500R

Отзывы:

Бренды по названию

Популярные бренды

Baumer GIM500R, Руководство пользователя

Результаты поиска

Содержание GIM500R

Отзывы:

Бренды по названию

Популярные бренды