Baumer 11233538 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 54

Baumer 11233538 Скачать руководство пользователя страница 40

8

|

Functions

Baumer

40

Operating Manual

OM20/ OM30 RS485 with Modbus RTU | V1

8.10

Function of the LED

In the factory settings, the function of the LED follows the alarm output. This means that the out-
put is activated as soon as no measured value can be recorded. The function of the LED can be
switched via Modbus RTU so that it follows the function of the parameterizable switching output.

Modbus RTU command – holding register: LED Function

Address 1102 – LED Function:

Address

Access

Number of
registers

Data type

Description

1102

Read/write

1

uint16_t

Determine the function of the LED:

n

100 = switching output

n

101 = alarm output

8.11

Function of the Teach button

With the Teach button function (

Local User Interface

), you have the option of specifying the

mode of the Teach button. You have a choice between the

Xpert

(factory setting) and

Xpress

modes. The mode is selected via Modbus RTU.

Adjustable parameters in the

Xpert

mode:

n

Zero position

n

Reset the sensor to the factory settings

Adjustable parameters in the

Xpress

mode:

n

Zero position

The Teach button is automatically deactivated after 5 min (timeout can be parameterized via
Modbus RTU).

Teaching the zero position (in the

Xpress

mode)

Instruction:

a) Place the measurement object at the desired position for the zero position.

b) Keep the Teach button pressed for 2 seconds.

ü

Green LED blinks with 2 Hz.

Result:

ü

Teach-In ok: Sensor goes back to the operating mode.

ü

Teach-in not OK: Green and yellow LEDs blink simultaneously with 8 Hz.

«
...
38
39
40
41
42
...
»

Содержание 11233538























































Отзывы:

Нет отзывов