Basler BE1-67N Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 75

background image

1-2

BE1-67N General Information

9190700990 Rev F

Figure 1-2. Zero Sequence Polarizing (Three-Winding Transformer)

Zero Sequence Voltage

Zero sequence voltage polarization is preferred for higher ground source impedances. Refer to Figures 1-
1 and 1-2 for relay connections that obtain zero sequence voltage (3V

0

) from a set of grounded wye-

broken delta voltage transformers. The voltage polarized relay has a directional polarization adjustment to
match the impedance angle of the protected line to the characteristic angle of the relay. This is the angle
about which the directional angle is centered. A choice of line angles allows the relay to be adjusted to
include the resistance component of the ground fault.

Dual Zero Sequence Current and Voltage

Dual polarization is preferred where ground source impedance varies, or to provide redundant
polarization. Dual polarization is achieved using a polarizing signal that is the phasor sum of the current
and voltage polarizing signals.

OUTPUT CONTACTS

BE1-67N relays have the following output contacts: relay status alarm (relay fail), tripping, and auxiliary
(optional).

Relay Status Alarm

A relay status alarm output contact (relay fail) indicates that proper voltages are not being supplied to the
internal relay circuitry or that the microprocessor self-diagnostics has detected an error. This alarm output
contact is normally closed.

Tripping

Normally open or normally closed tripping contacts are included for each function within the relay.
Configuration of these contacts is defined by the relay style number. These output contacts are used with
optionally selected target indicator circuits.

«
...
10
11
12
13
14
...
»

Содержание BE1-67N












































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-67N

Бренд: Zander Aachen Страницы: 4

Cooper Power Systems RLY-800

Бренд: Eaton Страницы: 14

Бренд: Solem Страницы: 20

Бренд: Nassar Страницы: 5

Бренд: Pilz Страницы: 27

Бренд: ZIEHL Страницы: 8

Бренд: Velleman Страницы: 40

FieldPoint cFP-RLY-425

Бренд: National Instruments Страницы: 16

Бренд: WEG Страницы: 148

Бренд: Viking Страницы: 4

Бренд: Tyco Страницы: 3

Superintend Trafox VR-16

Бренд: Muuntosahko Страницы: 8

Бренд: Domotime Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды