Basler BE1-67N Скачать руководство пользователя страница 15

Страница: 15 / 75

9190700990 Rev F

BE1-67N General Information

1-5

Range

50 Hz Nominal:

45 to 55 Hz

60 Hz Nominal:

55 to 65 Hz

Polarizing Current (I

)

Current Rating

Continuous: 10

Aac

1 Second:

150 Aac

Minimum Sensing Level

Directional Instantaneous:

Front-panel adjustable from 0.75 to 2.0 Aac

Time Overcurrent:

Fixed at 0.2 Aac

Burden

Maximum: <0.1

Polarizing Voltage (V

)

Maximum Rating (Line-to-Neutral)

Continuous: 240

Vac

1 Second:

360 Vac

Minimum Sensing Level

Directional Instantaneous:

4.0 Vac

Time Overcurrent:

0.75 Vac

Burden

At 120 Vac:

<1 VA

Operating Region

Operating region is

(150

window) centered about the characteristic angle.

Harmonic Sensitivity

Polarizing voltage is not affected by third or higher harmonics.

Characteristic Angle

Characteristic angle is switch-selectable to 0 or 60

. Characteristic angle accuracy is

for V

inputs

below 30 Vac and

for V

inputs greater than 30 Vac.

Directional Closing Band

Directional closing band is

centered about the characteristic angle.

Directional Unit

Response Time:

Within 15 ms to change in direction and magnitude

Repeatability:

Set angles are repeatable within

3% or 1

, whichever is greater

Time Overcurrent

Pickup Range

Sensing Input Range 1 and 2:

0.25 to 6 Aac

Sensing Input Range 3 and 4:

0.05 to 1.2 Aac

Pickup Accuracy

Within

5% of the expected value established by tap selector switch with the intertap adjustment at its

maximum clockwise setting.

Repeatability

Repeatability of pickup setting (combination of tap selector switch and intertap adjustment) is

2%.

Response Time Accuracy

Within

5% of the time value indicated on the characteristic time curve or 25 ms, whichever is greater.

Содержание BE1-67N












































































Результаты поиска

Содержание BE1-67N

Отзывы:

Похожие инструкции для BE1-67N

Бренды по названию

Популярные бренды

Basler BE1-67N, Инструкция по эксплуатации

Результаты поиска

Содержание BE1-67N

Отзывы:

Похожие инструкции для BE1-67N

Бренды по названию

Популярные бренды