manualshive.com logo in svg

Basler BE1-25/79TR, Инструкция по эксплуатации, Страница: 75 / 78

Поделиться
Скачать
Basler BE1-25/79TR Скачать руководство пользователя страница 75

BE1-25/79TR Testing

5-14

Step 7.

Verify that all contact sensing inputs are open.  Operate the Status/EDIT Down switch.

Observe that the relay completes the pre-programmed test sequence.  The sequence of
events (tests) is as follows:

HSR Target LED ON

LT1 Target LED ON

LT2 Target LED ON

PAR Target LED ON

PF Target LED ON

RP1 Target LED ON

RP2 Target LED ON

LO Target LED ON

LT1 Timing LED ON

LT2 Timing LED ON

RP1 Timing LED ON

RP2 Timing LED ON

PF Timing LED ON

PAR Timing LED ON

LO Timing LED ON

RST Timing LED ON

DB Control LED ON

LB Control LED ON

DL Control LED ON

LL Control LED ON

TRIP Control LED ON

CLOSE Control LED ON

25 Control LED ON

CE Control LED ON

CLOSE contacts close

TRIP contacts close

N.O. PROG 1 contacts close.

N.O. PROG 2 contacts close.

N.O. PROG 3 contacts close.

LT1 contact closes.

LT2 contact closes.

RP1 contact closes.

RP2 contact closes.

Normally closed RT ALM contacts opens.

SYNC contacts close

Allows Step 6 to be performed.

Step 8.

To terminate the test, operate the Reset switch.

Содержание BE1-25/79TR















































































Отзывы:

Нет отзывов