Basler BE1-25/79TR Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 78

Basler BE1-25/79TR Скачать руководство пользователя страница 18

BE1-25/79TR General Information

1-12

Counter Enable (CE).

Contact Sensing Inputs - Continued

High Speed Enable (HSR).
Block High Speed Reclose (BLK) for 3 phase faults.
Drive to Lockout (DTL).
Drive to Reset (DTR).

Serial Port Communications Front and rear panel mounted RS 232-C connectors (9-pin, D

subminiature female) for setting, testing, and data collection.

Time Delays

Refer to Table 1-2. Timing tolerance for HSR and SYNC timers is
±5% or two cycles, whichever is greater. All other timer tolerances
are ±5% or 50 milliseconds, whichever is greater.

Table 1-2. Time Delay Ranges

Number of Delays

Function

Range

2

Line Test (LT1, LT2)

1-999 seconds

2

Restore Power (RP1, RP2)

1-999 seconds

1*

Parallel (PAR)

1-999 seconds

1

Sync-Check (SYNC)

1-999 cycles

1

High Speed Reclose (HSR)

1-999 cycles

1**

Power Fail (PF)

1-99 seconds

2

Reset Time (RST1, RST2)

1-999 seconds

1

Lockout Time (LO)

1-999 seconds

1***

Master Time (MASTER)

1-999 seconds

1

Close Output (CLOSE TD)

1-999 seconds

1

Loss of Potential (LOP TD)

0.01-9.99 seconds

*

If the breaker is intended to operate open (parallel disabled) then the relay will go to reset
after the master timer times out and RST2 timer expires. The bus and line will both be
energized with the PAR input open.

**

The power failure function is a tripping function and will not start the master timer.

***

Master timer used is similar in principle to the mechanical repeat cycle (R.C.) timer in which
various operations are permitted as the cam rotates. If lockout has not been reached in the
preset time allotted, the master timer will time out and determine whether to go to lockout or
reset depending upon the state of the breaker and if the bus and line are Live with PAR input
disabled.

Outputs

All outputs are MOV protected.

(Isolated)

Trip, close, sync-check, relay trouble alarm (RT ALM) and memory.

Trip

One tripping contact with N.O. configuration.

Close

One closing contact with N.O. configuration.

Sync

The sync-check (PAR) function with voltage measuring circuits has
one output relay with a N.O. configuration.

Memory

There are four memory output relays, each with selectable N.O. or
N.C. contacts for line test or restore power.

«
...
16
17
18
19
20
...
»

Содержание BE1-25/79TR















































































Отзывы:

Нет отзывов