Basler BE1-25/79TR Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 78

Basler BE1-25/79TR Скачать руководство пользователя страница 68

BE1-25/79TR Testing

5-7

RP1 Timer

Step 13. Set the line voltage at a live level and the bus voltage at a dead level.

Step 14. Close the RP1 switch on the test set and trip the test set breaker.

Observe that the test set breaker closes and the RP1 target LED lights after the RP1 timer
counts down.

RP2 Timer

Step 15. Open the test set RP1 switch and close the RP2 switch.

Step 16. Trip the test set breaker and observe that after the RP2 timer counts down, the test set breaker

closes and the RP2 target LED lights.

Step 17. Verify that the RP targets extinguish when the Reset switch is operated.

Step 18. Open the RP2 switch on the test set.

PAR Timer

Step 19. Set the line and bus voltages at live levels, in phase, at system frequency.

Step 20. Close the PAR switch on the test set and trip the breaker.

Verify that the time from when the sync contacts close until the test set breaker closes equals
the desired parallel time delay.

Step 21. Open the PAR switch.

Verify that the PAR target LED extinguishes when the Reset switch is operated.

HSR Timer

Step 22. Trip the test set breaker and momentarily close the HSR switch on the test set.

After the HSR timer counts down, the test set breaker should close and the HSR target LED
should be ON. If high speed reclosing is being supervised by the sync function (HSR-SYNC
YES in the settings mode) then a high speed reclosure may not be initiated until sync contact
closure occurs.

Step 23. Operate the Reset switch and observe that the HSR target LED extinguishes.

Sync-Check Timer

Step 24. Trip the test set breaker.

After the sync time delay expires, the sync contacts should close and the relay 25 LED should
be ON.

Close breaker.

«
...
66
67
68
69
70
...
»

Содержание BE1-25/79TR















































































Отзывы:

Нет отзывов