manualshive.com logo in svg

Basler BE1-25/79TR, Инструкция по эксплуатации, Страница: 73 / 78

Поделиться
Скачать
Basler BE1-25/79TR Скачать руководство пользователя страница 73

BE1-25/79TR Testing

5-12

CALIBRATION

To calibrate the relay, perform the following steps.

Step 1.

Perform the preliminary setup procedures.

Step 2.

Operate the Settings Select UP or DOWN switch and observe SETTINGS MDE indicated on
display.

Step 3.

Operate the Settings Select UP or DOWN switch until CAL MODE NO is indicated on display.

Step 4.

Operate the Status/EDIT Up switch and observe CAL MODE YES indicated on display.

Step 5.

Operate the Reset switch while holding the Status/EDIT Up and observe Sel Sys Freq
indicated on display.

Step 6.

To select 50 Hz or 60 Hz operation, operate Settings Select UP or DOWN switch:

UP for 60 Hz?

DOWN 

for 50 Hz?

Step 7.

Verify the selection of system frequency by operating Status/EDIT Up switch and observe that
the following is displayed.

60 Hertz

Cal Mode 3 ph and Apply 110V if relay is 3 phase.

Cal Mode 1 ph and Apply 110V if relay is 1 phase.

50 Hertz

Cal Mode 3 ph and Apply 100V if relay is 3 phase.

Cal Mode 1 ph and Apply 100V if relay is 1 phase.

Step 8.

Apply specified voltage to bus and line inputs then operate the Settings Select UP for at least
one second.

Step 9.

Observe the results.

If a good calibration was achieved, the display will flash the following different displays.

If single phase type relay:

Phase Cal

Line 1 Ph

Cal OK Line

Bus 1 Ph

Cal OK Bus

followed by:  1 Ph Rng Done.

Содержание BE1-25/79TR















































































Отзывы:

Нет отзывов