Basler BE1-25/79TR Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 78

Basler BE1-25/79TR Скачать руководство пользователя страница 12

BE1-25/79TR General Information

1-6

Figure 1-4. Loop Station Application Example

and freezes the reclose timers any time this input is opened regardless of voltage monitor conditions.

Reclosing Example

Automated reclosing applications can be as simple or complex as your particular station requires. All
connections between BE1-25/79TR relays, monitoring inputs, and contact sensing inputs are not shown in
our example.

Our example, Figures 1-4 illustrates a typical three transformer looped station automated reclosing
application. In this example, four BE1-25/79TR relays are used. BE1-25/79TR relay number 1 is connected
across breaker 52-1 (Line 1 potential transformer (PT) feeds the relay line input and bus D PT feeds the
relay bus input). BE1-25/79TR relay number 2 is connected in a similar manner for breaker 52-2. BE1-
25/79TR relay number 3 is connected to motor operated switch 89-4 with bus D PT feeding the line input
and bus E PT feeding the bus input. BE1-25/79TR relay number 4 is connected in a similar manner for
motor operated switch 89-5, Bus F, and Bus E. When reclosing 89-4 and 89-5, 89-4 is set to close first.
Figures 1-5 through 1-8 illustrate connections for the four BE1-25/79TR relays in our example application.

Legend (for Figures 1-5 through 1-8)

43/A-Auto/Manual Switch

43C/ON-Carrier Switch ON

52b-Breaker Position

86-Lockout Relay

94-Aux Tripping Relay

BLK- Block High Speed Reclose

CE-Master Timer Enable

F/FCC-Power Fail Feature Cut-Out

H/FCC-High Speed Feature Cut-Out

HRC- High Speed Reclose Cancel

HRI-High Speed Reclose Initiate

HSR-High Speed Reclose Enable

LT1-First Line Test Enable

P/FCC-Parallel Feature Cut-Out

PAR-Parallel Enable

PF-Power Failure Enable

R/FCC-Restore Feature Cut-Out

RP1-First Restore Power Enable

T/FCC-Test Feature Cut-Out

«
...
10
11
12
13
14
...
»

Содержание BE1-25/79TR















































































Отзывы:

Нет отзывов