Baroness LM551B Скачать руководство пользователя страница 150 | Manualshive

Страница: 150 / 172

background image

Adjustment of Stoppers

Important

The installation method and installation
position of the stoppers differ depending on
the mower unit model.

The stopper is installed to prevent the mower
arm from interfering with the frame when
swiveling the mower units #2 and #3.
Install in the appropriate position.
Note:
The stopper is not used when the mower units
LS66 installed.
The stopper installation position for each
mower unit model is described below.

A: Installed at the lower position

LS62
LH52

1

2

A

3

euiiz5-001

Adjustment of Stoppers_001

1

Stopper

2

Nut

3

Spring washer

B: Installed at the upper position

LH62

1

3

2

B

euiiz5-002

Adjustment of Stoppers_002

･
･

･

1

Stopper

2

Nut

3

Spring washer

Adjustment of Mower Stopper Pin

The mower stopper pin can prevent or allow
tilting of the mower units.
Adjust according to the operating conditions.
Fixed:

The mowing line while traveling straight
ahead is a straight line. (The mowing line is
easy to see.)
The mower units do not tilt while operating
on slopes, and incomplete mowing can be
reduced.

Released:

It is appropriate when turning while mowing
or it is easy to follow undulations.
On a level surface, lower all mower units.
Apply the parking brake, and then stop the
engine.
Adjust the position of the mower stopper pin,
and then insert the cotter pin.

To fix:
Insert the cotter pin into the upper hole in the
mower stopper pin.

4

3

1

2

famlj4-003

Adjustment of Mower Stopper Pin_001

1

Mower stopper pin

2

Cotter pin

3

Mower arm

4

Mower coupling

･

･

･

1.
2.

3.

LM551B

Maintenance

Page 5-36

Maintenance Work

«
...
148
149
150
151
152
...
»

Содержание LM551B













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LM551B

Бренд: H&S Страницы: 32

Бренд: SANLI Страницы: 16

Craftsman 944.601181

Бренд: Sears Страницы: 52

Бренд: RedMax Страницы: 18

Бренд: Land Pride Страницы: 58

Бренд: Snapper Страницы: 28

Бренд: Yard-Man Страницы: 16

Бренд: Snapper Страницы: 24

Бренд: Spear & Jackson Страницы: 2

Бренд: Land Pride Страницы: 48

TLM530TRMS65-XP

Бренд: Toyama Страницы: 59

Бренд: Gardeo Страницы: 53

Бренд: Gardenline Страницы: 28

Бренд: GARDEO PRO Страницы: 99

Бренд: Gardena Страницы: 12

Бренд: Jonsered Страницы: 120

Бренд: Grillo Страницы: 44

Бренд: Craftsman Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды