Baroness LM551B Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 172

background image

Level 3

Danger

Danger

Since it will become extremely hot around the
exhaust outlet during DPF regeneration, do
not perform the regeneration in a location
where fires may occur.

Important

When the system enters the level where DPF
regeneration is required, perform the
regeneration immediately.
Interrupting the regeneration or ignoring the
warning and continuing traveling or cutting
work may cause the engine and DPF to
malfunction.

Important

If ignoring the parked regeneration
requirement and continuing traveling or cutting
work in PM accumulation "Level 3", PM
accumulation level enters "Level 4".
If still continuing traveling or cutting work, you
will not be able to operate this machine for
regeneration.

Important

Automatic regeneration can not be activated
in PM accumulation "Level 3".
Perform parked regeneration immediately.

You can not continue to use this machine
for traveling and cutting work during DPF
regeneration.
You can operate this machine to perform
the regeneration. (The fault diagnostic tool
is not required.)

･

･

These are the statuses in PM accumulation
"Level 3".

1

1

1 of 2

<

NEXT

>

HIDE

FMI 15

E x c e s s i v e P M 3

SPN 3701

C : 1

1 of 2

<

NEXT

>

HIDE

FMI 15

C O R R E C T I V E A C T I O N :
S t a r t D P F P a r k e d
R e g e n e r a t i o n
i m m e d i a t e l y

SPN 3701

C : 1

2

2

27gtuu-006

Level 3_001

1

LED (yellow)

2

Arrow key

"Excessive PM3" appears in the monitor
display.
Pressing an arrow key changes the
display to "CORRECTIVE ACTION: Start
DPF Parked Regeneration immediately".
The LED (yellow) lights up.
The engine output is limited at 50%.

Stop traveling and cutting work.
Park this machine in a safe location.
Apply the parking brake.
Set the throttle opening to 0% (idling).
If the DPF auto regeneration inhibit switch
set to the "Auto regeneration inhibit mode,"
set it to the "Auto regeneration mode."
Press the DPF parked regeneration switch.
Parked regeneration starts and the
regeneration icon changes from blinking to
lighting.
When the regeneration completed, the
regeneration icon disappears.

1.

･

･
･

2.
3.
4.
5.
6.

7.

8.

Maintenance

LM551B

Maintenance

Page 5-19

DPF

«
...
131
132
133
134
135
...
»

Содержание LM551B













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LM551B

Бренд: Partner Страницы: 10

Бренд: Partner Страницы: 76

Бренд: Vari Страницы: 42

Бренд: Neuton Страницы: 28

Commercial Front Cut Rider YHRK20

Бренд: Yazoo Страницы: 83

AMBROGIO L60 ELITE

Бренд: ZCS Страницы: 34

Бренд: Ryobi Страницы: 20

DR TRIMMER/MOWER SPRINT

Бренд: Country Home Products Страницы: 20

Бренд: LAZER Страницы: 17

Бренд: Garden Gear Страницы: 16

Бренд: Cub Cadet Страницы: 2

Бренд: Makita Страницы: 252

Бренд: Makita Страницы: 32

Бренд: Makita Страницы: 72

Бренд: Makita Страницы: 14

Бренд: Makita Страницы: 28

Бренд: Makita Страницы: 40

Бренд: Makita Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды