background image

Maintenance Work

Swiveling Mower Units #2 and #3

Caution

Both the reel cutter (cutting cylinder) and the
bed knife (bottom blade) are edged tools.
Handle them carefully, since they could cut
your hands or legs.

Caution

Be careful not to inhale exhaust gas while
swiveling the mower units.

B

A

sibu71-016

Swiveling Mower Units #2 and #3_001

A

Mower unit swivel angle 90°

B

Mower unit swivel angle 45°

Maintenance can be performed more easily
with mower units #2 and #3 swiveled.

Lower the mower units, and then stop the
engine.
Remove the pipe pin, and then remove the
grip pin.

1

2

sibu71-010

Swiveling Mower Units #2 and #3_002

1

Grip pin

2

Pipe pin

1.

2.

Swivel the mower unit toward the outside of
the main vehicle.

1

sibu71-011

Swiveling Mower Units #2 and #3_003

1

Mower unit

Fully insert the grip pin into the locking hole
for maintenance, and then install the pipe pin
in the grip pin.
The installation location for the locking hole
for maintenance differs depending on
whether the mower unit is installed in the
front or rear position.

Mower unit position: Front
Use the rear locking hole (A) for
maintenance.

1

A

2

sibu71-012

Swiveling Mower Units #2 and #3_004

1

Grip pin

2

Pipe pin

3.

4.

LM551B

Maintenance

Page 5-30

Maintenance Work

Содержание LM551B













































































































































































Отзывы: